Abstract:To alleviate the shortage of river sand (RS) and recycle abandoned resources, two recycled manufactured sands (RMSs) produced from tunnel excavation rock (tuff manufactured sand, TS) and granite cutting waste (granite manufactured sand, GS) are studied and compared with standard sand (SS) and RS. The aim is to identify the application potential of the two RMSs in cement-based materials. This is done by analyzing their influences on the mortar properties based on their surface characteristics and establishing a correlation between the surface characteristics of RMS and mortar properties. For the parent rock, petrographic analysis is performed and the uniaxial compressive strength is measured. For sand, the physical properties are evaluated and X-ray diffraction is used for analyzing the chemical composition. Digital image processing, nitrogen adsorption, and X-ray computed tomography are employed to determine the surface characteristics of sand particles. For the mortar, the fluidity, mechanical strength, water absorption, early total shrinkage, and accelerated expansion ratio are measured. The microstructure of the mortar interface transition zone is examined. Mercury intrusion porosimetry and thermogravimetric analysis are conducted to study the internal mechanism. The results indicate that compared with SS, the two RMSs reduce the fluidity of fresh mortar. In addition, TS is beneficial for the flexural, compressive, and tensile strengths of hardened mortar because of its denser internal pore structure and high degree of hydration caused by the properties of sand. The mechanical strength of the GS mortar can reach a similar or slightly higher level than that of the SS mortar. Furthermore, the fluidity and mechanical strength are well correlated with two parameters of sand, namely, roundness and specific surface area. The tensile strain capacity of the RMS-based mortar is superior to those of the SS and RS mortars. However, RMS increases the early total shrinkage. Although the TS mortar has the highest tensile strain capacity, it also has the largest early total shrinkage among the four mortar mixtures. Comparing the escalations in tensile strain capacity and early total shrinkage, the TS increases the risk of shrinkage cracking in the early stages. The effect of GS on the mortar tensile strain capacity is slightly greater than that on the early total shrinkage; thus, there is no significant influence on the risk of early shrinkage cracking in the GS mortar. In the accelerated expansion test, the TS shows potential alkali-silica reaction (ASR) risk in accordance with ASTM C1260, however, the GS indicates no potential for expansion damage. Based on the performance of various sands and mortars, GS has a better application value than TS. As for the TS mortar, it is necessary to consider the shrinkage cracking risk and ASR hazard in practical applications.

Optimized reinforcement of granite residual soil using a cement and alkaline solution: A coupling effect

Addition of alkaline solutions and fibers for the reinforcement of kaolinite-containing granite residual soil

The Effect of Organic and Inorganic Modifiers on the Physical Properties of Granite Residual Soil

Application Potential of Granite Cutting Waste and Tunnel Excavation Rock As Fine Aggregates in Cement-Based Materials Based on Surface Characteristics

The Effect of Different Fibers on Granite Residual Soil Reinforced with Alkaline Solution

The Effect of Length and Content of Fiber on Glass Fiber and Basalt Fiber-Reinforced Granite Residual Soil

Water Retention Behavior and Shear Strength of Artificially Cemented Granite Residual Soil Subjected to Free Drying

Isotropic Compression and Triaxial Shear Behaviors of Cement- and Cement-Gravel-treated Granite Residual Soil for Use As Subgrade Filling

Effects of Cement Treatment on Mechanical Properties and Microstructure of a Granite Residual Soil

Macro-porosity and Skeleton of a Cement-Gravel-treated Granite Residual Soil for Subgrade from CT Scanning

Synergistic effects of recycled demolition waste and GGBS-FA based geopolymers on the mechanical properties and stabilization mechanism of high plasticity clay

Mechanical and microstructural properties of recycling granite residual soil reinforced with glass fiber and liquid-modified polyvinyl alcohol polymer

Preparation and Characterization of Low-Carbon Cementitious Materials Based on Soda-Residue-Activated Ground Granulated Blast-Furnace Slag: A Case Study on Cemented Paste Backfills

Influence of calcined sediment inputs on the mechanical behavior of fiber-reinforced concrete in an aggressive environment

Mechanics, durability, and microstructure analysis of marine soil stabilized by an eco-friendly calcium carbide residue-activated coal gangue geopolymer

Multiscale experimental analysis of marine clay stabilized with coal gangue–calcium carbide residue geopolymer

Physical-chemical coupling excitation of low activity coal gasification slag solid waste and its application as a backfill cementitious material

Mechanical Properties and Mechanism of Geopolymer Cementitious Materials Synergistically Prepared Using Red Mud and Yellow River Sand

Effectiveness of Soda Residue-Activated GGBS As Alternative Binder on Compressive Strength and Workability of Cemented Paste Backfills: Reuse of Multi-Source Solid Wastes

Mechanical properties and microscopic mechanism of solid waste based binder solidified stone waste

Study on the Synergistic Preparation of Supplementary Cementitious Materials from Multiple Solid Wastes: Bayer Red Mud and Gold Tailings