Abstract:To alleviate the shortage of river sand (RS) and recycle abandoned resources, two recycled manufactured sands (RMSs) produced from tunnel excavation rock (tuff manufactured sand, TS) and granite cutting waste (granite manufactured sand, GS) are studied and compared with standard sand (SS) and RS. The aim is to identify the application potential of the two RMSs in cement-based materials. This is done by analyzing their influences on the mortar properties based on their surface characteristics and establishing a correlation between the surface characteristics of RMS and mortar properties. For the parent rock, petrographic analysis is performed and the uniaxial compressive strength is measured. For sand, the physical properties are evaluated and X-ray diffraction is used for analyzing the chemical composition. Digital image processing, nitrogen adsorption, and X-ray computed tomography are employed to determine the surface characteristics of sand particles. For the mortar, the fluidity, mechanical strength, water absorption, early total shrinkage, and accelerated expansion ratio are measured. The microstructure of the mortar interface transition zone is examined. Mercury intrusion porosimetry and thermogravimetric analysis are conducted to study the internal mechanism. The results indicate that compared with SS, the two RMSs reduce the fluidity of fresh mortar. In addition, TS is beneficial for the flexural, compressive, and tensile strengths of hardened mortar because of its denser internal pore structure and high degree of hydration caused by the properties of sand. The mechanical strength of the GS mortar can reach a similar or slightly higher level than that of the SS mortar. Furthermore, the fluidity and mechanical strength are well correlated with two parameters of sand, namely, roundness and specific surface area. The tensile strain capacity of the RMS-based mortar is superior to those of the SS and RS mortars. However, RMS increases the early total shrinkage. Although the TS mortar has the highest tensile strain capacity, it also has the largest early total shrinkage among the four mortar mixtures. Comparing the escalations in tensile strain capacity and early total shrinkage, the TS increases the risk of shrinkage cracking in the early stages. The effect of GS on the mortar tensile strain capacity is slightly greater than that on the early total shrinkage; thus, there is no significant influence on the risk of early shrinkage cracking in the GS mortar. In the accelerated expansion test, the TS shows potential alkali-silica reaction (ASR) risk in accordance with ASTM C1260, however, the GS indicates no potential for expansion damage. Based on the performance of various sands and mortars, GS has a better application value than TS. As for the TS mortar, it is necessary to consider the shrinkage cracking risk and ASR hazard in practical applications.

Effects of Cement Treatment on Mechanical Properties and Microstructure of a Granite Residual Soil

Macro-porosity and Skeleton of a Cement-Gravel-treated Granite Residual Soil for Subgrade from CT Scanning

Application Potential of Granite Cutting Waste and Tunnel Excavation Rock As Fine Aggregates in Cement-Based Materials Based on Surface Characteristics

Water Retention Behavior and Shear Strength of Artificially Cemented Granite Residual Soil Subjected to Free Drying

Isotropic Compression and Triaxial Shear Behaviors of Cement- and Cement-Gravel-treated Granite Residual Soil for Use As Subgrade Filling

Sedimentation-affected Engineering Performances and Microstructures of a Hybrid Portland- Sulfate Aluminate Cement Grout Cast in Long Tubes

Optimized reinforcement of granite residual soil using a cement and alkaline solution: A coupling effect

Experimental Study on Engineering Properties of Cemented Soil with High Water Content

Effect of cementation on the small-strain stiffness of granite residual soil

Microscopic Evolution of Pore Characteristics and Particle Orientation of Granite Residual Soil in One-Dimensional Compression

Effect of Initial Conditions on the Pore Structure and Bimodal Soil–Water Characteristic Curve of Compacted Granite Residual Soil

Investigation on the Microstructure, Unconfined Compressive Strength, and Thermal Conductivity of Compacted CDG Soil by MICP Treatment during Curing

Experimental study on shear and disintegration resistance of MICP-treated residual granite soil

Unsaturated soil properties of MICP treated granitic residual soil of Shantou region of China

X-ray Microtomography Study on the Cemented Structure of Cemented Granular Materials

Effects of Drying-Wetting Cycles on the Mechanical Behavior of Reconstituted Granite-Residual Soils

Effect of Fiber Content on Mechanical Properties of Fiber-Reinforced CGF All-Solid-Waste Binder-Solidified Soil

Synergistic effects of recycled demolition waste and GGBS-FA based geopolymers on the mechanical properties and stabilization mechanism of high plasticity clay

Effects of drying-wetting cycles and free iron oxides on the mechanical behaviors of a partially decomposed granite residual soils

Experimental study on physical properties of superfine cement grouting material

Study on the Strength and Micro Characteristics of Grouted Specimens with Different Superfine Cement Contents