Abstract:Formamidinium‐based (FA) 2D perovskites have emerged as highly promising candidates in solar cells. However, the insertion of 2D spacer cations into the perovskite lattice concomitantly introduces micro‐strain and unfavorable orientations that hinder efficiency and stability. In this study, by finely tuning the FA‐based 2D perovskite lattice through spacer cation engineering, we achieved a stable lattice structure with balanced distortion, micro‐strain relaxation, and reduced carrier‐lattice interactions. These advancements effectively stabilize the inherently soft lattice against light and thermal aging stress, particularly extreme temperature changes. To reduce the photocurrent loss induced by undesired crystal texture, we further employed a polarity‐matched molecular‐type selenourea (SENA) additive to modulate the crystallization kinetics. The introduction of the SENA significantly inhibits the disordered crystallization induced by spacer cations and drives the templated growth of the quantum well structure with a vertical orientation. This controlled crystallization process effectively reduces crystal defects and enhances charge separation. Ultimately, the optimized FA‐based perovskite photovoltaic devices achieved a remarkable power conversion efficiency (PCE) of 20.03% (certified steady‐state efficiency of 19.30%), setting a new record for low‐n 2D perovskite solar cells. Furthermore, the devices exhibited less than 1% efficiency degradation after operating at maximum power point for 1000 hours and maintained 92.3% and 91.1% of the initial efficiency after aging at 85°C for 720 hours and 50 cycles of cold‐warm shock, respectively. This article is protected by copyright. All rights reserved

High efficiency formamidinium‐cesium perovskite‐based radio‐photovoltaic cells

Organic‐Salt‐Assisted Crystal Growth and Orientation of Quasi‐2D Ruddlesden–Popper Perovskites for Solar Cells with Efficiency over 19%

Stable and Bright Formamidinium-Based Perovskite Light-Emitting Diodes with High Energy Conversion Efficiency.

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

Vertical Recrystallization for Highly Efficient and Stable Formamidinium-Based Inverted-Structure Perovskite Solar Cells

High-efficiency and thermally stable FACsPbI3 perovskite photovoltaics

Oriented Low‐n Ruddlesden‐Popper Formamidinium‐Based Perovskite for Efficient and Air Stable Solar Cells

Strong Electron Acceptor of a Fluorine-Containing Group Leads to High Performance of Perovskite Solar Cells

Formamidinium-incorporated Dion-Jacobson phase 2D perovskites for highly efficient and stable photovoltaics

Over 24% Efficient Poly(vinylidene fluoride) (PVDF)‐Coordinated Perovskite Solar Cells with a Photovoltage up to 1.22 V

Suppressing charge recombination in a methylammonium-free wide-bandgap perovskite film for high-performance and stable perovskite solar cells

Uniform Phase Permutation of Efficient Ruddlesden–Popper Perovskite Solar Cells via Binary Spacers and Single Crystal Coordination

Realizing Stable Artificial Photon Energy Harvesting Based on Perovskite Solar Cells for Diverse Applications.

Perovskite seeding growth of formamidinium-lead-iodide-based perovskites for efficient and stable solar cells

High-performance alpha-voltaic cell based on a 4H-SiC PIN junction diode

Enhanced Resonance for Facilitated Modulation of Large-Area Perovskite Films with Stable Photovoltaics

Highly Stable and Efficient Formamidinium‐Based 2D Ruddlesden–Popper Perovskite Solar Cell via Lattice Manipulation

Over 25% Efficiency and Stable Bromine-free RbCsFAMA-based Quadruple Cation Perovskite Solar Cells Enabled by an Aromatic Zwitterion

Highly Efficient Prismatic Perovskite Solar Cells

High Efficiency Near-Infrared And Semitransparent Non-Fullerene Acceptor Organic Photovoltaic Cells

Ionic Liquid Stabilized Perovskite Solar Modules with Power Conversion Efficiency Exceeding 20%