Abstract:Formamidinium (FA)-based 2D perovskites have emerged as highly promising candidates in solar cells. However, the insertion of 2D spacer cations into the perovskite lattice concomitantly introduces microstrain and unfavorable orientations that hinder efficiency and stability. In this study, by finely tuning the FA-based 2D perovskite lattice through spacer cation engineering, a stable lattice structure with balanced distortion, microstrain relaxation, and reduced carrier-lattice interactions is achieved. These advancements effectively stabilize the inherently soft lattice against light and thermal-aging stress. To reduce the photocurrent loss induced by undesired crystal texture, a polarity-matched molecular-type selenourea (SENA) additive is further employed to modulate the crystallization kinetics. The introduction of the SENA significantly inhibits the disordered crystallization induced by spacer cations and drives the templated growth of the quantum well structure with a vertical orientation. This controlled crystallization process effectively reduces crystal defects and enhances charge separation. Ultimately, the optimized FA-based perovskite photovoltaic devices achieve a remarkable power conversion efficiency (PCE) of 20.03% (certified steady-state efficiency of 19.30%), setting a new record for low-n 2D perovskite solar cells. Furthermore, the devices exhibit less than 1% efficiency degradation after operating at maximum power point for 1000 h and maintain excellent stability after thermal aging and cycles of cold-warm shock, respectively. A delicate selection of spacer cations and polarity-matched molecular additives is presented to manipulate the 2D perovskite lattice, improving related texture and stability. The optimized FA-based 2D perovskite photovoltaic devices achieve a remarkable power conversion efficiency of 20.03% (certified efficiency of 19.30%). Furthermore, the devices exhibit less than 1% efficiency degradation after operation at maximum power point for 1000 h.image

Vertical Recrystallization for Highly Efficient and Stable Formamidinium-Based Inverted-Structure Perovskite Solar Cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Reconstructing Subsurface Lattice for Stable Perovskite Photovoltaics

Oriented Nucleation in Formamidinium Perovskite for Photovoltaics

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

Stable Formamidinium‐Based Perovskite Solar Cells Via in Situ Grain Encapsulation

Oriented Low‐n Ruddlesden‐Popper Formamidinium‐Based Perovskite for Efficient and Air Stable Solar Cells

Highly Stable and Efficient Formamidinium‐Based 2D Ruddlesden–Popper Perovskite Solar Cell via Lattice Manipulation

Highly Stable and Efficient Formamidinium-Based 2D Ruddlesden-Popper Perovskite Solar Cells via Lattice Manipulation

Highly Efficient Inverted Planar Solar Cell Using Formamidinium-Based Quasi-Two Dimensional Perovskites

Efficient and Stable Wide‐Bandgap Perovskite Solar Cells Derived from a Thermodynamic Phase‐Pure Intermediate

Controlling Intermediate Phase Formation to Enhance Photovoltaic Performance of Inverted FA-Based Perovskite Solar Cells

Defect suppression and energy level alignment in formamidinium-based perovskite solar cells

A-site Assisted Perovskite Crystallization Via Ion-Exchange MOFs for High Efficient and Stable Perovskite Solar Cells

Dual‐Interface Modification for Inverted Methylammonium‐Free Perovskite Solar Cells of 25.35% Efficiency with Balanced Crystallization

Formamidinium Lead Iodide‐Based Inverted Perovskite Solar Cells with Efficiency over 25% Enabled by An Amphiphilic Molecular Hole‐Transporter

Regulating the Crystallization of FAPbI3‐Based Perovskite with a Furan Substituted Ethylammonium Additive for Achieving Highly Efficient Solar Cells

Reduction of Bulk and Surface Defects in Inverted Methylammonium- and Bromide-Free Formamidinium Perovskite Solar Cells

Zwitterion-Stabilizing Scalable Bladed -Phase Cs<sub>0.1</sub>FA<sub>0.9</sub>PbI<sub>3</sub> Films for Efficient Inverted Planar Perovskite Solar Cells

Amide‐Catalyzed Phase‐Selective Crystallization Reduces Defect Density in Wide‐Bandgap Perovskites

Effects of Formamidinium and Bromide Ion Substitution in Methylammonium Lead Triiodide Toward High-Performance Perovskite Solar Cells