Abstract:It is an effective strategy to improve the performance of quasi-two-dimensional (Q-2D) perovskite solar cells (PSCs) by introducing fluoro-substituted aromatic alkylammonium spacer cations into the active layer. Herein, the influence of the benzylammonium (BA) and the x-fluorobenzylammonium (xFBA) cation, in which x stands for the substitution position of the benzene ring (o, ortho; m, meta; p, para), on the crystal orientation, phase distribution, film morphology of the Q-2D (n = 5) perovskite films, and the corresponding device performance is systematically evaluated. The result suggests that compared with BA and oFBA, mFBA and pFBA have a larger dipole moment, forming a dense perovskite film with gradient structures where the n = 1 2D perovskite mainly exists at the top of the film and the large n-phase perovskite exists at the bottom of the film. Encouragingly, the (pFBA)2MA4Pb5I16 (MA = CH3NH3+)-based perovskite solar cells achieve the highest efficiency of 17.12%, with an open-circuit voltage of 1.175 V, a short-circuit current density of 18.50 mA cm–2, and a fill factor of 78.78%, which is significantly higher than those of BA (14.07%)-, oFBA (12.89%)-, and mFBA (14.67%)-based PSCs. Furthermore, pFBA-based devices also exhibit the best stability compared to the other three devices.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.chemmater.2c00146.1H NMR spectra and molecular dipole moments of BAI, oFBAI, mFBAI, and pFBAI; UPS spectra of BA-, oFBA-, mFBA-, and pFBA-based n = 5 2D perovskite and the corresponding (αhv)2 vs hv curves of 2D perovskites; J–V curves of BA-, oFBA-, mFBA-, and pFBA-based Q-2D PSCs with forward and reverse scans; EDS mapping of different elements (C, N, I, Pb, Cl) of perovskite films with different cations; TA spectra for different n phases as a function of delay time of the four films; formation energy of the 2D perovskite corresponding to cations; series resistance (Rs), charge-transport resistance (Rct), and recombination resistance (Rrec) derived from EIS for different PSCs and VTFL form SCLC for different PSCs; and experimental crystallographic parameters of (oFBA)2PbI4 (PDF)This article has not yet been cited by other publications.

Highly Efficient Inverted Planar Solar Cell Using Formamidinium-Based Quasi-Two Dimensional Perovskites

High‐Efficiency Quasi‐2D Perovskite Solar Cells Incorporating 2,2′‐biimidazolium Cation

Two-Dimensional Perovskite Solar Cells with 14.1% Power Conversion Efficiency and 0.68% External Radiative Efficiency

Highly Efficient and Stable Inverted Planar Solar Cells from (fai)x(mabr)1−xpbi2 Perovskites

Oriented Low‐n Ruddlesden‐Popper Formamidinium‐Based Perovskite for Efficient and Air Stable Solar Cells

Quasi-2D Perovskite with Symmetrical N Value Interface Enables a Certified Efficiency over 21.5%

Excitonic Solar Cells Using 2D Perovskite of (Ba)2(fa)2pb3i10

Band Alignment Boosts over 17% Efficiency Quasi-2D Perovskite Solar Cells via Bottom-Side Phase Manipulation

Vertically Oriented 2d Layered Perovskite Solar Cells with Enhanced Efficiency and Good Stability

Highly Stable and Efficient Formamidinium‐Based 2D Ruddlesden–Popper Perovskite Solar Cell via Lattice Manipulation

Selectively Fluorinated Benzylammonium-Based Spacer Cation Enables Graded Quasi-2D Perovskites for Efficient and Stable Solar Cells

Highly Efficient and Stable Planar Perovskite Solar Cells with Modulated Diffusion Passivation Toward High Power Conversion Efficiency and Ultrahigh Fill Factor

Highly Efficient and Stable 2D 3D Perovskite Solar Cells Fabricated by Interfacial Modification

Highly Stable and Efficient Formamidinium-Based 2D Ruddlesden-Popper Perovskite Solar Cells via Lattice Manipulation

Over 21% Efficiency Stable 2D Perovskite Solar Cells

Zwitterion-Stabilizing Scalable Bladed -Phase Cs<sub>0.1</sub>FA<sub>0.9</sub>PbI<sub>3</sub> Films for Efficient Inverted Planar Perovskite Solar Cells

A Thermodynamically Favored Crystal Orientation in Mixed Formamidinium/Methylammonium Perovskite for Efficient Solar Cells

Formamidinium-incorporated Dion-Jacobson phase 2D perovskites for highly efficient and stable photovoltaics

Suppressing charge recombination in a methylammonium-free wide-bandgap perovskite film for high-performance and stable perovskite solar cells

High‐Quality Pure‐Phase MA‐Free Formamdinium Dion‐Jacobson 2D Perovskites for Stable Unencapsulated Photovoltaics

Effect of the Device Architecture on the Performance of FA(0.85)MA(0.15)PbBr(0.45)I(2.55) Planar Perovskite Solar Cells