Abstract:Formamidinium‐based (FA) 2D perovskites have emerged as highly promising candidates in solar cells. However, the insertion of 2D spacer cations into the perovskite lattice concomitantly introduces micro‐strain and unfavorable orientations that hinder efficiency and stability. In this study, by finely tuning the FA‐based 2D perovskite lattice through spacer cation engineering, we achieved a stable lattice structure with balanced distortion, micro‐strain relaxation, and reduced carrier‐lattice interactions. These advancements effectively stabilize the inherently soft lattice against light and thermal aging stress, particularly extreme temperature changes. To reduce the photocurrent loss induced by undesired crystal texture, we further employed a polarity‐matched molecular‐type selenourea (SENA) additive to modulate the crystallization kinetics. The introduction of the SENA significantly inhibits the disordered crystallization induced by spacer cations and drives the templated growth of the quantum well structure with a vertical orientation. This controlled crystallization process effectively reduces crystal defects and enhances charge separation. Ultimately, the optimized FA‐based perovskite photovoltaic devices achieved a remarkable power conversion efficiency (PCE) of 20.03% (certified steady‐state efficiency of 19.30%), setting a new record for low‐n 2D perovskite solar cells. Furthermore, the devices exhibited less than 1% efficiency degradation after operating at maximum power point for 1000 hours and maintained 92.3% and 91.1% of the initial efficiency after aging at 85°C for 720 hours and 50 cycles of cold‐warm shock, respectively. This article is protected by copyright. All rights reserved

Quasi-2D Perovskite with Symmetrical N Value Interface Enables a Certified Efficiency over 21.5%

Two-Dimensional Perovskite Solar Cells with 14.1% Power Conversion Efficiency and 0.68% External Radiative Efficiency

High‐Efficiency Quasi‐2D Perovskite Solar Cells Incorporating 2,2′‐biimidazolium Cation

Band Alignment Boosts over 17% Efficiency Quasi-2D Perovskite Solar Cells via Bottom-Side Phase Manipulation

Highly Efficient Inverted Planar Solar Cell Using Formamidinium-Based Quasi-Two Dimensional Perovskites

Oriented Low‐n Ruddlesden‐Popper Formamidinium‐Based Perovskite for Efficient and Air Stable Solar Cells

Over 21% Efficiency Stable 2D Perovskite Solar Cells

Water‐Assisted Crystal Growth in Quasi‐2D Perovskites with Enhanced Charge Transport and Photovoltaic Performance

Organic‐Salt‐Assisted Crystal Growth and Orientation of Quasi‐2D Ruddlesden–Popper Perovskites for Solar Cells with Efficiency over 19%

Quantum Well Growth Management to Smooth the Energy Transfer Pathway for Quasi‐2D Perovskite Solar Cells

Vertically-aligned quasi-2D cesium lead halide perovskite solar cells

High-performance quasi-2D perovskite solar cells with power conversion efficiency over 20% fabricated in humidity-controlled ambient air

Organic-inorganic Hybrid Quasi-2D Perovskites Incorporated with Fluorinated Additives for Efficient and Stable Four-Terminal Tandem Solar Cells

Graded 2D/3D Perovskite Heterostructure for Efficient and Operationally Stable MA‐Free Perovskite Solar Cells

A Thermodynamically Favored Crystal Orientation in Mixed Formamidinium/Methylammonium Perovskite for Efficient Solar Cells

Highly Stable and Efficient Formamidinium‐Based 2D Ruddlesden–Popper Perovskite Solar Cell via Lattice Manipulation

Over-18%-Efficiency Quasi-2D Ruddlesden–Popper Pb–Sn Mixed Perovskite Solar Cells by Compositional Engineering

Efficient and Stable Quasi‐2D Perovskite Solar Cells Enabled by Thermal‐Aged Precursor Solution

Two-dimensional Perovskite Solar Cells with High Luminescence and Ultra-Low Open-Circuit Voltage Deficit

Highly Efficient and Stable Solar Cells Based on Crystalline Oriented 2D/3D Hybrid Perovskite

Orientation Regulation of Phenylethylammonium Cation Based 2D Perovskite Solar Cell with Efficiency Higher Than 11%