Abstract:Polypropylene‐LD sludge composite for erosive environment In the present investigation, a steel industry waste Linz–Donawitz (LD) sludge was added in different proportions with a polypropylene (PP) matrix and composite specimens were manufactured using the hand layup method. Experiments were performed to study the physical, mechanical, and erosion wear properties of the PP–LD sludge composites. This investigation also includes scanning electron microscopy (SEM), and x‐ray diffraction analysis of filler and composites. The erosion wear tests were carried out by Taguchi's experimental array design, where the effect of five control factors (impingement angle, filler content, erodent size, impact velocity, and erodent temperature) on erosion rate was analyzed. It was observed that filler content is the most influencing factor affecting were rate of the composites. At the maximum filler content of 20 wt%, the compressive strength and hardness increased to 85.71 MPa and 0.643 GPa, respectively. The tensile strength of the composites marginally decreased by 12.97% with the addition of 20 wt% filler. It was further observed that the flexural strength of the neat polymer decreased from 29.23 to 22.98 MPa with the addition of 20 wt% LD sludge. The SEM pictures of the eroded surface exhibited that the material removal is due to micro cracking and crack propagation. Highlights In this study, an industrial waste (LD sludge) is successfully used as a potential filler material in the PP matrix. Physical and mechanical properties of the PP‐LD sludge composites are analyzed. Effects of different parameters like filler content, impact velocity, impingement angle, erodent size and erodent temperature on the wear behavior are studied. Scanning electron microscopy is carried out so that a micro‐examination of the surfaces can be performed, as well as an assessment of the wear derbies.

Effect of pistachio shell particles on mechanical and erosion wear performance of hybrid kenaf/glass polyester composites

An investigation on the mechanical, thermal and tribological properties of newly developed polyester composites made with Pistachio shell particles for industrial applications

Influence of Load and Sliding Velocity on Abrasive Wear of Polyester Composites Reinforced with Bio-Particulates as Filler Material

Investigation of Mechanical Attributes and Dynamic Mechanical Analysis of Hybrid Polyester Composites for Automotive Applications

A comprehensive experimental study of eco-friendly hybrid polymer composites using pistachio shell powder and Aquilaria agallocha Roxb

Mechanical, rheological, thermal and morphological properties of pistachio shell powder reinforced / linear low-density polyethylene/polyolefin elastomer biocomposites

Influence of layering variation with addition of bio-fillers on mechanical and thermal performances of hybrid polyester composites

Optimization and Prediction of Wear Characteristics of Khas Khas Grass/Mesquite Bark Powder/Banana Fiber-Reinforced Epoxy Green Hybrid Composites Using Taguchi Technique

Influence of fish-scale powder addition and stacking order on mechanical and thermal properties of hybrid kenaf/glass polyester composites

Development and erosion wear analysis of polypropylene/Linz‐Donawitz sludge composites

Microstructural, mechanical, and tribological properties of a novel hybrid LLDPE/PTFE/x wt.% GNPs for bearing surface applications

The effects of filler type on the friction and wear performance of PEEK and PTFE composites under hybrid wear conditions

Mechanical, thermal, and fatigue behavior of aloe vera fiber/pistachio shell powder toughened epoxy resin composite

Comparison of the usage of nut shell, walnut shell, and pistachio shell as a reinforcement particle on the mechanical and wear performance of polypropylene

Abrasive wear behaviour of orange peel (biowaste) particulate reinforced polymer composites

Effect of tungsten carbide on mechanical and tribological properties of jute/sisal/E-glass fabrics reinforced natural rubber/epoxy composites

Influence of suspended cenospheres on the mechanical characteristics and wear loss of natural fiber-reinforced hybrid composites: implications for biomedical applications and sustainable material management

Effects of the Mesoporous Filler and Oleophilic Property on the Tribological Behavior of Polyetheretherketone Composites.

Influence of Particle Size on the Mechanical Performance and Sintering Quality of Peanut Husk Powder/PES Composites Fabricated through Selective Laser Sintering

Study on the Friction and Sliding Wear Behavior of Hybrid Polytetrafluoroethylene/Kevlar Fabric Composites Filled with Polyphenylene Sulfide

Wear and Frictional Performance of Epoxy Composites Reinforced with Natural Waste Fibers and Fillers for Engineering Applications