Abstract:Semi-continuous direct-chill (DC) casting holds a prominent position in commercial aluminium alloy processing, especially in production of large sized ingots. Macrosegregation, which is the non-uniform chemical composition over the length scale of a casting, is one of the major defects that occur during this process. The fact that macrosegregation is essentially unaffected by subsequent heat treatment (hence constitutes an irreversible defect) leaves us with little choice but to control it during the casting stage. Despite over a century of research in the phenomenon of macrosegregation in castings and good understanding of underlying mechanisms, the contributions of these mechanisms in the overall macrosegregation picture; and interplay between these mechanisms and the structure formation during solidification are still unclear. This review attempts to fill this gap based on the published data and own results. The following features make this review unique: results of computer simulations are used in order to separate the effects of different macrosegregation mechanisms. The issue of grain refining is specifically discussed in relation to macrosegregation. This report is structured as follows. Macrosegregation as a phenomenon is defined in the Introduction. In “Direct-chill casting – process parameters, solidification and structure patterns” section, direct-chill casting, the role of process parameters and the evolution of structural features in the as-cast billets are described. In “Macrosegregation in direct-chill casting of aluminium alloys” section, macrosegregation mechanisms are elucidated in a historical perspective and the correlation with DC casting process parameters and structural features are made. The issue of how to control macrosegregation in direct-chill casting is also dealt with in the same section. In “Role of grain refining” section, the effect of grain refining on macrosegregation is introduced, the current understanding is described and the contentious issues are outlined. The review is finished with conclusion remarks and outline for the future research.

Rationalizing Al-Mg, Al-Mg-Si, and multicomponent aluminum alloy design with segregation susceptibility predictions

Effect of Mo on Segregation Behavior of Al-Mg-Si-Mn Alloy Produced by Twin-Roll Casting

Experimental Characterization and First-Principles Calculations of Zn Segregation at the Β″-Mg5al2si4/al Interfaces in Al-Mg-Si Alloys

Interfacial Segregation and Precipitates Behavior in the Ultrafine Grained Al-based Metal Matrix Composites

First-principles investigation of the Mg, Cu segregation at Al Σ5 (310) and Σ9 (221) symmetrical tilt grain boundaries

Study on Micro Segregation of High Alloy Fe–Mn–C–Al Steel

Segregation of S precipitates at T/Al interfaces and relevant effects on localized corrosion mechanisms in Al-Cu-Mg alloy

Macrosegregation in a multicomponent low alloy steel

Solute segregation in polycrystalline aluminum from hybrid Monte Carlo and molecular dynamics simulations with a unified neuroevolution potential

Effect of Mg and Si contents and TiC nanoparticles on the center segregation susceptibility of twin-roll cast Al-Mg-Si alloys

Construction and analysis of surface phase diagrams to describe segregation and dissolution behavior of Al and Ca in Mg alloys

Understanding of macro-segregation in direct-chill cast 2024 alloy with intensive melt shearing based on the evolution of microstructure and temperature field

Strength and ductility enhancement of twin-roll cast Al-Zn-Mg-Cu alloys with high solidification intervals through a synergistic segregation-controlling strategy

Enhancing mechanical properties of twin-roll cast Al–Mg–Si–Fe alloys by regulating Fe-bearing phases and macro-segregation

Monitoring the effect of alloying elements segregation in Fe Mn Ni Al high Entropy alloy

Simulation of the Dendrite Morphology and Microsegregation in Solidification of Al–Cu–Mg Aluminum Alloys

Significance of segregation on grain refinement and property improvement in extruded Mg-Al-Mn alloy with moderate Al content

Modeling of Microsegregation and Homogenization of 6xxx Al-Alloys Including Precipitation and Strengthening During Homogenization Cooling

Modeling of microsegregation in macrosegregation computations

Macrosegregation in direct-chill casting of aluminium alloys

Predicting Grain Boundary Segregation in Magnesium Alloys: An Atomistically Informed Machine Learning Approach