Abstract:Platform preheating is a common strategy towards reducing residual stress and distortion of additively manufactured metal components by powder bed fusion – laser beam (PBF-LB) due to the lowered thermal gradient. However, platform preheating can lead to in-situ ageing for aluminium alloy components in the building process, which will affect the mechanical properties. In this work, the microstructures of PBF-LB AlSi10Mg built on preheated (150 °C) and un-preheated (ambient) platforms have been characterized in detail by various electron microscopy techniques in order to better understand the influence of platform preheating on mechanical properties. Furthermore, the influences of T5 ageing and solution treatment plus ageing (T6) on microstructure and mechanical properties have also been examined. Platform preheating to 150 °C improves strength, which is associated with the in-situ precipitation of granular or rod-shaped Si phase and needle-like β'' phase. To the best of our knowledge, this is the first report on the observation of β'' precipitates in PBF-LB Al–Si–Mg alloys in the as-built state. Upon T5 treatment, the ambient platform material exhibits significant age hardening while only marginal age hardening is observed for the 150 °C platform material. Consequently, the materials built at different platform temperatures show similar mechanical properties after T5 treatment. The age hardening response is more pronounced when a rapid solution treatment (RST, 520 °C for 10 min) is adopted instead of the conventional solution treatment (CST, 520 °C for 2 h) owing to the precipitation of a higher number density of needle-like β'' phase during ageing. The T5 treatment improves both yield strength and tensile strength, but the improvements in strength are accompanied by a reduction in ductility. On the other hand, the RST-T6 treatment substantially improves ductility and reduces the tensile strength while maintaining the yield strength for the 150 °C platform material. Based on the microstructural analysis, the influences of platform preheating and post-build heat treatment on mechanical properties of PBF-LB AlSi10Mg are discussed.

Laser‐Based Closed‐Loop Controlled Heat Treatment for Residual Stress Relief of Additively Manufactured AlSi10Mg Components

High-Temperature Mechanical Properties of Stress-Relieved AlSi10Mg Produced via Laser Powder Bed Fusion Additive Manufacturing

In-situ control of residual stress and its distribution in a titanium alloy additively manufactured by laser powder bed fusion

Mechanical Properties of AlSi10Mg Processed by Laser Powder Bed Fusion at Elevated Temperature

Evolution of interphase stress over a crack propagation plane as a function of stress relief heat treatments in a PBF‐LB/M AlSi10Mg alloy

Additive Manufacturing of AlSi10Mg and Ti6Al4V Lightweight Alloys via Laser Powder Bed Fusion: A Review of Heat Treatments Effects

Tailoring heat treatment for AlSi7Mg0.6 parts with as-built surface generated by laser powder bed fusion to reduce surface roughness sensitivity

Effect of laser process parameters on thermal behavior and residual stress of high-strength aluminum alloy processed by laser powder bed fusion

Mitigation of Residual Stress and Distortion of AlSi10Mg Parts Produced by Laser Powder Bed Fusion through a Proper Selection of Support Geometry

Microstructural analysis of the influences of platform preheating and post-build heat treatment on mechanical properties of laser powder bed fusion manufactured AlSi10Mg alloy

Micromechanical Modeling of AlSi10Mg Processed by Laser-Based Additive Manufacturing: From as-Built to Heat-Treated Microstructures

Laser Powder Bed Fusion of Inconel 718: Residual Stress Analysis Before and After Heat Treatment

The impact of heat treatment on microstructure, residual stress, and mechanical behavior of laser powder bed fusion additively manufactured Ti–6Al–2Sn–4Zr–2Mo alloy

Influence of Stress Relief Annealing Parameters on Mechanical Properties and Decomposition of Eutectic Si Network of L-PBF Additive Manufactured Alloy AlSi10Mg

Advancements in metal additive manufacturing: In-situ heat treatment of aluminium alloys during the laser powder bed fusion process

Assessing the thermal stability of laser powder bed fused AlSi10Mg by short-period thermal exposure

Modification of Residual Stresses in Laser Additive Manufactured AlSi10Mg Specimens Using an Ultrasonic Peening Technique

Implemented in-situ heat treatment process for controlling the residual thermal stresses during the fabrication of Ti-6Al-4V titanium alloy through additive manufacturing

Thermo-mechanical simulation of annealing heat treatment of Ni-based GH4099 superalloy made by laser powder bed fusion

Residual Stress Mapping in Heat-Assisted Additive Manufacturing of IN 718: An X-Ray Diffraction Study

The effect of the iso‐thermal heat treatment on the microstructure and properties of powder bed fusion‐laser beam AlSi10Mg alloy