Abstract:Failures in reinforced concrete (RC) structural walls have been reported to occur at longitudinal lap splices in earthquakes as far back as 1964 (Kunze et al. in JP 62:635–650, 1965) and as recently as 2023 (Pujol et al. in ES 63:777, 2024). Design codes such as ACI318-19 (2019) and JSCE Standard Specification for Concrete Structures (2007) have been adjusted accordingly and have banned the placement of lap splices near sections where longitudinal reinforcement is expected to yield in reinforced concrete structural walls. But minimizing lap splice vulnerabilities in new construction does not address existing buildings that may be vulnerable to earthquakes because of lap splices placed at or near critical sections. A simple, rapid assessment technique should be adopted to address the large number of existing buildings with potentially vulnerable RC walls. To investigate the deformation capacity of structural walls with lap splices near sections where longitudinal reinforcement yields, a two-part experimental program is ongoing: four large-scale walls with non-staggered lap splices were tested at Purdue University (Pollalis Drift capacity of reinforced concrete walls with lap splices, Purdue University: West Lafayette, 2021) and two large-scale walls with staggered lap splices have been tested at the University of Canterbury (Kerby et al. Experimental study of staggered lap splices in RC structural walls, 2023). Results from these six tests are added to a dataset of 15 previous tests of walls with non-staggered lap splices compiled by Almeida et al. (JSE 143:853, 2017). A method to estimate drift capacity of walls with lap splices is proposed based on estimates of lap splice strength, steel stress–strain relationships, and moment-area theorems. Two sets of assumptions can be used to produce estimates of drift capacity. The first set of assumptions applies when detailed information of reinforcement stress–strain relationships is available, and the second set of assumptions applies when reinforcement stress–strain relationships must be assumed. Both sets of assumptions produce reasonable estimates of the drift capacity of walls with lap splices, and the second set of assumptions can be used for rapid assessment given minimal information about the detailing and material properties of a wall.

Empirical drift capacity models for fully grouted reinforced masonry shear walls

Cyclic Response of Infilled RC Frames with Window and Door Openings: Experimental Results and Damage Interpretation

Experimental Study of RC Frames with Window and Door Openings Under Cyclic Loading

Experimental Study of Cement Mortar-Steel Fiber Reinforced Rammed Earth Wall

Enhanced empirical models for predicting the drift capacity of less ductile RC columns with flexural, shear, or axial failure modes

Experimental Studies on Behavior of Fully Grouted Reinforced-Concrete Masonry Shear Walls

On estimating the drift capacity of reinforced concrete walls with lap splices at their bases

The Hysteretic Failure Features of Reinforced Masonry Shear Walls Revealed by Modeling Experimental Residual Strain Data

Quasi-static, Cyclic Loading Tests of RAC Brick Masonry Walls Strengthened by Basalt Textile Reinforced Concrete

Effective Prediction of Concrete Constitutive Models for Reinforced Concrete Shear Walls under Cyclic Loading

In-plane shear strength and damage fragility functions for partially-grouted reinforced masonry walls with bond-beam reinforcement

Experimental and Numerical Study on the Seismic Performance of Prefabricated Reinforced Masonry Shear Walls

Displacement-based Deformation Capacity Design Method of RC Cantilever Walls

Experimental Analysis of Out-of-plane Behavior of Masonry Infill Walls Strengthened with Textile Reinforced Mortar and Wall Post in Autoclaved Aerated Concrete Frames

Seismic behavior and modeling of T‐shaped reinforced concrete walls under high axial force ratios

Deformation Capacity and Performance-Based Seismic Design for Reinforced Concrete Shear Walls

Experimental Study of FRP-Reinforced Slotted RC Shear Walls under Cyclic Loading

Out-of-plane strengthening of URM walls using different fiber-reinforced materials

New OpenSees Material Model for Simulating Reinforced Concrete Shear Walls Subjected to Coupled Axial Tension and Cyclic Lateral Loads

Analytical modeling of masonry load-bearing walls

Accuracy of stochastic finite element analyses for the safety assessment of unreinforced masonry shear walls