Abstract:Crystallinity (Xc) is a crucial crystallographic factor that related closely to mechanical properties in linear polyethylene or high density polyethylene (HDPE), whose molecular weight (MW) is at a 105 level. However, as a typically intractable-processing polymer, the structure-property relationship concerned Xc is still ambiguous for ultrahigh molecular weight polyethylene (UHMWPE) with MW﹥1.5×106. The reason is that high entanglement density hinders chain mobility in the course of UHMWPE crystallization, thus crystalline degree in UHMWPE molding parts is difficult to be artificially modulated within a wide scope. In this study, low chain-entanglement status of UHMWPE melt was achieved by (1) utilizing lowly entangled nascent UHMWPE synthesized via the single-site Ziegler-Natta catalyst, and (2) decreasing the sintered temperature. It is impressive that partial disentanglement reserved in the melt is favorable for obtaining higher crystallinity. Meanwhile, an isothermal crystallization treatment was additionally adopted to further improve the capacity of regulating crystallization after the traditional two-step sintering procedure. By a combination of varying the initial entanglement in nascent powders, sintering temperature, isothermal crystallization duration, and molecular weight of UHMWPE, the Xc of the compression-sintered products has been successfully adjusted in the relatively broad range of 29%≦ Xc≦65%, which offered an opportunity to validly survey the correlation between mechanical property and crystallinity. Particular attention was paid to the yield strength. A linear master straight-line can be plotted as yield strength vs. Xc for all of the samples inspected, indicating crystallinity also plays a dominant role on mechanical performances of UHMWPE sintering parts, as same in the case of HDPE. However, the mechanical reinforcement induced by increment of Xc in UHMWPE is more efficient than in HDPE. The yield strength of UHMWPE is much higher than that of HDPE at the same Xc, indicating the amorphous phase or entanglements in UHMWPE is crucial to determine the mechanical property. These findings are of significance for guiding the manufacturing of high-performance UHMWPE materials via crystallization manipulation.

Mechanical Properties of Ultra High Molecular Weight Polyethylene Obtained with Different Cocatalyst Systems

Rheology of Ultra High Molecular Weight Polystyrene

Thermal and Mechanical Properties of Ultrahigh-Molecular-Weight Ethylene/1-Hexene Copolymers Prepared by Living Polymerization with Fluorinated Bis(Phenoxy-Imine) Titanium(Iv) Catalyst

PREPARATION OF ULTRA HIGH MOLECULAR WEIGHT POLYETHYLENE USING STRUCTURED NANOPARTICAL ZIEGLER-NATTA CATALYSTS

Studies on Nonisothermal Crystallization of Ultra–high Molecular Weight Polyethylene in Liquid Paraffin

Study of the effect of the nature of catalyst systems on the molecular structure and properties of ultra-high molecular weight polyethylene

Theoretical Study on the High Polymer Molecular Weight of Heteroatom-Substituted Constrained Geometry Catalyst

UHMWPE with Short‐chain Branches Synthesized by Alkenyl Substituted Phenoxy–imine Catalysts in Ethylene Polymerization

Impact Properties of Metallocene-Catalyzed Ethylene-Alpha-Olefin Copolymers

Mechanical Properties of Polyethylene-Carbon Nanotube Composites Synthesized by In Situ Polymerization Using Metallocene Catalysts

Preparation of Weakly Entangled and Fine-sized Ultra-High-Molecular Weight Polyethylene by a MgCl2-Based Ziegler–Natta Catalyst

A hemi-metallocene chromium catalyst with trimethylaluminum-free methylaluminoxane for the synthesis of disentangled ultra-high molecular weight polyethylene

Improving the performance of a catalytic system for the synthesis of ultra high molecular weight polyethylene with a reduced number of entanglements

The mechanical properties of the ultra high molecular weight polyethylene grafted with 3-dimethy (3-(N-methacryamido) propyl) ammonium propane sulfonate

Reduced Entanglement Density of Ultrahigh-Molecular-Weight Polyethylene Favored by the Isolated Immobilization on the MgCl2 (110) Plane

Morphology and Plastic Yielding of Ultrahigh Molecular Weight Polyethylene

Crystallization Rates of Moderate and Ultrahigh Molecular Weight Polyethylene Characterized by Flash DSC Measurement

Synthesis of Ultra-High-Molecular-Weight Polyethylene with an Elevated Melting Point in an Octafluorobutane Medium

Pursuit of the correlation between yield strength and crystallinity in sintering-molded UHMWPE

Dynamic Mechanical Properties and Morphology of High‐density Polyethylene/caco3 Blends with and Without an Impact Modifier

A Novel Catalytic System of [O,O] Bidentate Titanium Complexes and Et2AlCl/Bu2Mg for the Production of Ultra‐High Molecular Weight Polyethylene