An Improved Analytical Thermal Rating Method for Cable Joints

He,Xie,Wang,Wu,Bao,Wang,Xu,Meng,Liu

DOI: https://doi.org/10.3390/en17092040

IF: 3.2

2024-04-26

Energies

Abstract:To improve the utilization rate of cable lines while retaining sufficient security, the accurate thermal assessment of cable is significant for cable operation condition evaluation. The thermal rating for a cable joint, which is regarded as a hot spot of cable lines, is not covered by the scope of IEC 60287. While the existing publications for cable joint thermal evaluation also have some limitations. In this paper, the quasi-three-dimensional thermal model of the cable joint was established and the iterative solution method for the model is presented. Based on the model, an improved thermal rating method for the cable joint was proposed, which was implemented with monitored surface temperature and load data. The improved method was verified by the finite element method and the results showed an error of less than 5%. The superiority of the improved method was conducted by the comparison between the previously published method and the improved method. The improved method showed a better accuracy than the previously published method. The proposed method in this paper can be complementary to the IEC method, and is easy to use for the operating evaluation of cable joints in the field with the on-line condition monitoring technology.

energy & fuels

What problem does this paper attempt to address?

This paper attempts to solve the thermal evaluation problem of cable joints to improve the utilization rate of existing cable lines and ensure their safety. Specifically:

1. **Importance of Thermal Evaluation of Cable Joints**:
- Cable joints are hot - spot areas in cable lines and are prone to serious power accidents such as insulation material degradation, partial discharge, breakdown, and even explosion and fire due to overheating.
- The IEC 60287 standard does not cover the thermal evaluation of cable joints, and the existing thermal evaluation methods for cable joints have limitations.

2. **Research Objectives**:
- Establish an improved thermal evaluation method for cable joints to more accurately evaluate the temperature distribution of cable joints under different loads, thereby improving the safety and utilization rate of cable lines.
- Propose a quasi - three - dimensional (quasi - 3D) thermal model and provide an iterative solution method for this model.

3. **Main Contributions**:
- The proposed improved method combines the monitored surface temperature and load data and is verified by the Finite Element Analysis (FEA) with an error of less than 5%.
- Compared with the existing methods, the improved method has higher accuracy and is easy to be combined with online monitoring techniques and applied in practical engineering.

### Formula Summary

- **Conductor Temperature Change Rate**:
\[
A\frac{dQ}{dx}=q\rho
\]
where \(A\) is the cross - sectional area of the conductor, \(q\) is the current density, and \(\rho\) is the thermal resistivity of the conductor.

- **Conductor Joule Loss**:
\[
Q_c = I^2R_{20}[1+\alpha(T - 20)]
\]
where \(I\) is the cable load current, \(R_{20}\) is the conductor resistance at 20°C, and \(\alpha\) is the resistance temperature coefficient.

- **Total Radial Thermal Resistance**:
\[
T_t=\sum_{i = 1}^{n}\frac{\ln(d_{i+1}/d_i)}{2\pi\lambda_i}
\]
where \(\lambda_i\) is the thermal conductivity of each layer of material, and \(d_i\) and \(d_{i+1}\) are the inner and outer diameters of each layer respectively.

- **Second - Order Non - homogeneous Differential Equation of Conductor Temperature**:
\[
\left\{
\begin{aligned}
&a_2\frac{d^2\theta}{dx^2}-a_1\theta+M = 0\\
&a_2=\frac{1}{aT_t}\\
&a_1=\frac{I^2R_{20}T_t}{q}\\
&M=\frac{I^2R_{20}}{q}-\frac{T_t}{q}q_0
\end{aligned}
\right.
\]

Through these formulas and methods, researchers can more accurately evaluate the thermal performance of cable joints, thereby providing a scientific basis for the safe operation of cable lines.