Abstract:Solar cavity receiver is a vital component in a solar power tower (SPT) system, where concentrated solar irradiation is absorbed, converted into heat and carried away by a kind of heat transfer fluid. The cavity receiver usually suffers from the high-flux and non-uniform concentrated solar irradiation, which would cause local overheating, large temperature gradient and even thermal stress fracture of the receiver and bring challenges for the safety of its daily operation. Therefore, it is necessary to investigate the thermal and mechanical performance of the solar cavity receiver. In the present study, a superheated water/steam solar cavity receiver with three boiling panels and a superheater was chosen as the physical model. An integrated simulation method, which couples the Monte-Carlo ray tracing (MCRT) method, the appropriate heat transfer correlations, the finite volume method (FVM) and the finite element method (FEM), was employed to simulate the complicated heat transfer process inside the receiver and conduct the thermal stress analysis for the absorber panels. With this method, the three-dimensional wall temperature and thermal stress distributions were gained both on the boiling panels and the superheater, and the causes of thermal stress induced by different temperature gradients were analyzed in detail. The following results were obtained: 1) The heat flux, wall temperature and equivalent thermal stress distributions all appear highly non-uniform on the absorber panels; 2) The hot spots can be found on the membrane wall between the elbows of the boiling panels, which can easily generate the high thermal stress due to the large temperature gradient with their surroundings; 3) The bi-axial stress at the outer and inner radius of the boiling tubes can be created by the large radial temperature gradient, and the thermal stress varies as a cosine distribution across the circumference of the superheated tubes, which is induced by the large temperature gradient in the circumferential direction. Besides, the spot-like areas with high thermal stress can also be found on the superheated tubes due to the considerable nonlinear axial temperature gradient. Moreover, the thermal stress on the membrane wall connected with both the boiling and the superheated tubes has the definite directionality, which shows parallel to the tubes or perpendicular to the tubes; 4) The thermal stress concentration always occurs at the high-temperature and structural discontinuity locations. Here, the thermal stress of the superheater is 360 MPa higher than that of the boiling panels. In general, the superheater has both the higher wall temperature and thermal stress, which is more crucial for the safe operation of the superheated water/steam solar cavity receiver.

Thermal and fluid dynamic analysis of a flat manifold microchannel heat sink in parabolic trough solar collector with optical errors

An Efficient 3D Tube-Level Flux-Thermal Model of External Tubular Receivers in Solar Power Tower Systems

Integrated Model for Comprehensive Performance Investigation of Solar Concentrated Photovoltaic‐Thermal System Embedded with Microchannel Heat Sinks

Measurement and correction on optical-thermal conversion of tubular solar cavity receiver with errors of installation and incident energy

Study on the uneven flow distribution and non-uniform heat transfer in microchannels

Thermal Management of Ultra High Concentrator Photovoltaic Cells: Analysing the Impact of Sintered Porous Media Microchannel Heat Sinks

Thermal-fluid-mechanical analysis of tubular solar receiver panels using supercritical CO2 as heat transfer fluid under non-uniform solar flux distribution

Dynamic Performance Analysis of Photovoltaic–thermal Solar Collector with Dual Channels for Different Fluids

Thermal performance investigation of the newly shaped vacuum tubes of parabolic trough collector system

ANALYSIS OF THE PERFORMANCE FOR A CONCENTRATING PHOTOVOLTAIC/THERMAL SOLAR SYSTEM

Numerical Investigation on Uniformity of Heat Flux for Semi-Gray Surfaces Inside a Solar Cavity Receiver

A coupled optical-thermal-fluid-mechanical analysis of parabolic trough solar receivers using supercritical CO2 as heat transfer fluid

Microchannel cooling of concentrator photovoltaics: A review

Thermal Characteristics and Thermal Stress Analysis of a Superheated Water/steam Solar Cavity Receiver under Non-Uniform Concentrated Solar Irradiation

Temperature homogenization control of parabolic trough solar collector field based on hydraulic calculation and extended Kalman filter

Analysis Of A Concentrating Photovoltaic/Thermal Solar System

Investigation of the enhancement of heat transfer in a flat plate solar collector with a corrugated tube under thermosiphon effect

Analysis of Thermal Performance and Thermal Stress Using Two-Dimensional Thermoelastic Model for a 50 MWe External Cylindrical Solar Receiver

Flow and Heat Transfer Performance of Array Finned Channel Coupled Jet Heat Sink

Experimental investigation and analytical prediction of a multi-channel flat heat pipe thermal performance

Sensitive Analysis for the Efficiency of a Parabolic Trough Solar Collector Based on Orthogonal Experiment