Abstract:Solar cavity receiver is a vital component in a solar power tower (SPT) system, where concentrated solar irradiation is absorbed, converted into heat and carried away by a kind of heat transfer fluid. The cavity receiver usually suffers from the high-flux and non-uniform concentrated solar irradiation, which would cause local overheating, large temperature gradient and even thermal stress fracture of the receiver and bring challenges for the safety of its daily operation. Therefore, it is necessary to investigate the thermal and mechanical performance of the solar cavity receiver. In the present study, a superheated water/steam solar cavity receiver with three boiling panels and a superheater was chosen as the physical model. An integrated simulation method, which couples the Monte-Carlo ray tracing (MCRT) method, the appropriate heat transfer correlations, the finite volume method (FVM) and the finite element method (FEM), was employed to simulate the complicated heat transfer process inside the receiver and conduct the thermal stress analysis for the absorber panels. With this method, the three-dimensional wall temperature and thermal stress distributions were gained both on the boiling panels and the superheater, and the causes of thermal stress induced by different temperature gradients were analyzed in detail. The following results were obtained: 1) The heat flux, wall temperature and equivalent thermal stress distributions all appear highly non-uniform on the absorber panels; 2) The hot spots can be found on the membrane wall between the elbows of the boiling panels, which can easily generate the high thermal stress due to the large temperature gradient with their surroundings; 3) The bi-axial stress at the outer and inner radius of the boiling tubes can be created by the large radial temperature gradient, and the thermal stress varies as a cosine distribution across the circumference of the superheated tubes, which is induced by the large temperature gradient in the circumferential direction. Besides, the spot-like areas with high thermal stress can also be found on the superheated tubes due to the considerable nonlinear axial temperature gradient. Moreover, the thermal stress on the membrane wall connected with both the boiling and the superheated tubes has the definite directionality, which shows parallel to the tubes or perpendicular to the tubes; 4) The thermal stress concentration always occurs at the high-temperature and structural discontinuity locations. Here, the thermal stress of the superheater is 360 MPa higher than that of the boiling panels. In general, the superheater has both the higher wall temperature and thermal stress, which is more crucial for the safe operation of the superheated water/steam solar cavity receiver.

A coupled optical-thermal-fluid-mechanical analysis of parabolic trough solar receivers using supercritical CO2 as heat transfer fluid

A coupled optical-thermal-fluid-mechanical analysis of parabolic trough solar receivers using supercritical CO<sub>2</sub> as heat transfer fluid

Buoyancy effects on convective heat transfer of supercritical CO2 and thermal stress in parabolic trough receivers under non-uniform solar flux distribution

Thermal Performance Analysis of a Parabolic Trough Solar Collector Using Supercritical CO2 As Heat Transfer Fluid under Non-Uniform Solar Flux

Thermal-fluid-mechanical analysis of tubular solar receiver panels using supercritical CO2 as heat transfer fluid under non-uniform solar flux distribution

Thermal-hydraulic performance analysis of a novel parabolic trough receiver with double tube for solar cascade heat collection

A Design Method and Numerical Study for a New Type Parabolic Trough Solar Collector with Uniform Solar Flux Distribution

Improving overall heat transfer performance of parabolic trough solar receiver by helically convex absorber tube

Numerical Investigation on Heat Transfer of Supercritical CO2 in Solar Receiver Tube in High Temperature Region

Thermal performance and thermal stress analysis of a supercritical CO2 solar conical receiver under different flow directions

Performance analyses and heat transfer optimization of parabolic trough receiver with a novel single conical strip insert

Coupling Effect Between Heat Flux Distribution and Buoyancy of Supercritical CO2 Heat Transfer with Nonuniform Heat Flux in Parabolic-Trough Collector

Thermal Characteristics and Thermal Stress Analysis of a Superheated Water/steam Solar Cavity Receiver under Non-Uniform Concentrated Solar Irradiation

Numerical simulation of a parabolic trough solar collector with nonuniform solar flux conditions by coupling FVM and MCRT method

Effects of geometric and operating parameters on thermal performance of conical cavity receivers using supercritical CO2 as heat transfer fluid

Numerical Investigations on Coupled Heat Transfer and Synthetical Performance of a Pressurized Volumetric Receiver with MCRT–FVM Method

Hydrothermal performance assessment of a parabolic trough with proposed conical solar receiver

Study on the convective heat transfer characteristics of supercritical CO 2 in mini-channels under unilateral heating conditions for application in a compact solar receiver

Numerical study on the stress and thermal performance of a supercritical CO 2 solar conical cavity receiver

Study on Heat Transfer and Stress Characteristics of the Pressurized Volumetric Receiver in Solar Power Tower System

Multi-scale Numerical Analysis of Flow and Heat Transfer for a Parabolic Trough Collector