Abstract:Solar cavity receiver is a vital component in a solar power tower (SPT) system, where concentrated solar irradiation is absorbed, converted into heat and carried away by a kind of heat transfer fluid. The cavity receiver usually suffers from the high-flux and non-uniform concentrated solar irradiation, which would cause local overheating, large temperature gradient and even thermal stress fracture of the receiver and bring challenges for the safety of its daily operation. Therefore, it is necessary to investigate the thermal and mechanical performance of the solar cavity receiver. In the present study, a superheated water/steam solar cavity receiver with three boiling panels and a superheater was chosen as the physical model. An integrated simulation method, which couples the Monte-Carlo ray tracing (MCRT) method, the appropriate heat transfer correlations, the finite volume method (FVM) and the finite element method (FEM), was employed to simulate the complicated heat transfer process inside the receiver and conduct the thermal stress analysis for the absorber panels. With this method, the three-dimensional wall temperature and thermal stress distributions were gained both on the boiling panels and the superheater, and the causes of thermal stress induced by different temperature gradients were analyzed in detail. The following results were obtained: 1) The heat flux, wall temperature and equivalent thermal stress distributions all appear highly non-uniform on the absorber panels; 2) The hot spots can be found on the membrane wall between the elbows of the boiling panels, which can easily generate the high thermal stress due to the large temperature gradient with their surroundings; 3) The bi-axial stress at the outer and inner radius of the boiling tubes can be created by the large radial temperature gradient, and the thermal stress varies as a cosine distribution across the circumference of the superheated tubes, which is induced by the large temperature gradient in the circumferential direction. Besides, the spot-like areas with high thermal stress can also be found on the superheated tubes due to the considerable nonlinear axial temperature gradient. Moreover, the thermal stress on the membrane wall connected with both the boiling and the superheated tubes has the definite directionality, which shows parallel to the tubes or perpendicular to the tubes; 4) The thermal stress concentration always occurs at the high-temperature and structural discontinuity locations. Here, the thermal stress of the superheater is 360 MPa higher than that of the boiling panels. In general, the superheater has both the higher wall temperature and thermal stress, which is more crucial for the safe operation of the superheated water/steam solar cavity receiver.

Numerical study on the stress and thermal performance of a supercritical CO 2 solar conical cavity receiver

Thermal performance and thermal stress analysis of a supercritical CO2 solar conical receiver under different flow directions

Numerical investigation on heat transfer and thermoelastic stress in a solar cavity receiver

Effects of geometric and operating parameters on thermal performance of conical cavity receivers using supercritical CO2 as heat transfer fluid

Numerical Investigation on Heat Transfer of Supercritical CO2 in Solar Receiver Tube in High Temperature Region

Thermal Characteristics and Thermal Stress Analysis of a Superheated Water/steam Solar Cavity Receiver under Non-Uniform Concentrated Solar Irradiation

Thermal-Mechanical Coupling Analysis of Spiral Tube in Solar Cavity Receiver

Thermal Performance and Thermal Stress Analysis of a 600 MWth Solar Cylinder External Receiver

Thermal-hydraulic-structural analysis and optimization of supercritical CO2 solar tower receiver

Analysis of Thermal Performance and Thermal Stress Using Two-Dimensional Thermoelastic Model for a 50 MWe External Cylindrical Solar Receiver

Coupled optical and thermal simulation of the thermal performance of a 50 MWe external cylindrical solar receiver

Experimental Study on Thermal Performance of a Water/steam Cavity Receiver with Solar Simulator

Study on the convective heat transfer characteristics of supercritical CO 2 in mini-channels under unilateral heating conditions for application in a compact solar receiver

A coupled optical-thermal-fluid-mechanical analysis of parabolic trough solar receivers using supercritical CO<sub>2</sub> as heat transfer fluid

Thermal-fluid-mechanical analysis of tubular solar receiver panels using supercritical CO2 as heat transfer fluid under non-uniform solar flux distribution

Numerical Evaluation on the Thermal Performance of the Solar External Cylinder Receiver Using Monte Carlo Ray-Tracing Algorithm

Numerical Study of New-Type Receiver with Axially-Hollow Spiral Deflector for Parabolic Trough Direct-Steam-Generation Loop of Concentrating Solar Power System

A coupled optical-thermal-fluid-mechanical analysis of parabolic trough solar receivers using supercritical CO2 as heat transfer fluid

Study on Heat Transfer and Stress Characteristics of the Pressurized Volumetric Receiver in Solar Power Tower System

Experimental Study Of The Thermal Performance Of Solar Cavity Receiver During Start-Up Process

Thermal performance analysis of a novel Conical-Cylindrical-Conical cavity receiver for a Scheffler concentrated solar system