Abstract:The broad technological concept as so-called "hybrid additive manufacturing" is introduced into the fabrication of flexible strain sensing structure, employing the combination process of fused deposition modeling (FDM) 3D printing technique and ultrasonic cavitation-enabled treatment. We customize the FDM settings to print auxetic structures with a negative Poisson's ratio (NPR), using the flexible thermoplastic polyurethane (TPU) material. Then, we employ the ultrasonic cavitation-enabled treatment conducted towards the flexible auxetic structure immersing in carbon nanotubes (CNTs) liquid, aiming to embed the CNTs into the surface layer of the auxetic structures. It is equivalent to two additive manufacturing steps, proving effective in designing and fabricating flexible strain sensors. Instead of 3D printing after the hybridization of the TPU matrix material, this manufacturing procedure can ensure that the intrinsic excellent mechanical properties of TPU are not weakened due to the internally mixed conductive materials but able to exhibit usable sensing performances. The Poisson's ratio of the sensor structure is -0.8. The sensor achieves over 300% strain. The sensitivity within the initial strain range is 2.661. The reliability of signal acquisition during the cyclic deformations is proved. Its response-recovery duration under 5% strain at 500 mm/min deformation rate is 130 ms(response)-250 ms(recovery). It gives accurate feedback to external stimuli at different frequencies. It can maintain stable output signals during 3000 cycles of stretching. It also can sense 1% minor-strain stimuli. The strain sensing behavior of the fabricated flexible sensor with the auxetic structure is detailed. The CNTs are combined tightly with the TPU surface layer to form a conductive network with variable resistance during recoverable deformation of the auxetic structure. The macro and micro-mechanisms of sensing are dissected, considering the tunneling effect of discontinuous CNTs. The hybrid additive manufacturing process is verified to be feasible, credible, and low-cost for easy fabrication of flexible strain sensors with complex geometry configurations.

Multi-Material 3D Printed Bendable Smart Sensing Structures

Smart structures with embedded flexible sensors fabricated by fused deposition modeling-based multimaterial 3D printing

Flex-Structural Embedded Flexible Strain Sensor via 3D Printing

High-Performance Auxetic Bilayer Conductive Mesh-Based Multi-Material Integrated Stretchable Strain Sensors.

Photocurable Polymer-Based 3D Printing: Advanced Flexible Strain Sensors for Human Kinematics Monitoring

Bidirectional and Stretchable Piezoresistive Sensors Enabled by Multimaterial 3D Printing of Carbon Nanotube/Thermoplastic Polyurethane Nanocomposites

Additive Manufacturing of Flexible Strain Sensors based on Smart Composites for Structural Health Monitoring with High Accuracy and Fidelity

4D printed multifunctional wearable strain sensors with programmable sensing characteristics

Three-Dimensional Printed Wearable Sensors with Liquid Metals for Detecting the Pose of Snakelike Soft Robots.

Direct 3D Printing of Highly Anisotropic, Flexible, Constriction-Resistive Sensors for Multidirectional Proprioception in Soft Robots.

Printed, Soft, Nanostructured Strain Sensors for Monitoring of Structural Health and Human Physiology

Embedded 3D Printing of Strain Sensors within Highly Stretchable Elastomers

Fabrication of high sensitivity and stable strain sensors based on composite folded structures via embedded 3D printing

3D Printing-Induced Hierarchically Aligned Nanocomposites With Exceptional Multidirectional Strain Sensing Performance

Self-healing flexible strain sensor fabricated through 3D printing template sacrifice for motion monitoring with enhanced healing and mechanical performance

A stretchable flexible strain sensor with high sensitivity and fast response fabricated by embedded 3D printing of the hybrid polydimethylsiloxane/conductive carbon paste composites

Three-Dimensional Printed Carbon Black/PDMS Composite Flexible Strain Sensor for Human Motion Monitoring

A Simple, Low-Cost Conductive Composite Material for 3D Printing of Electronic Sensors

3D Printing of Flexible Strain Sensor Array Based on UV‐Curable Multiwalled Carbon Nanotube/Elastomer Composite

3D Printing of Stretchable Strain Sensor Based on Continuous Fiber Reinforced Auxetic Structure

TPU/CNTs Flexible Strain Sensor with Auxetic Structure Via a Novel Hybrid Manufacturing Process of Fused Deposition Modeling 3D Printing and Ultrasonic Cavitation-Enabled Treatment