Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Characterization and comparison of deposits in a coal-fired rotary kiln for iron ore fluxed pellets and acidic pellets productions

Investigations of the effect of unburnt pulverized coal on the deposit formation mechanism in a rotary kiln for fluxed pellet production

Effects of Pellet Basicity on the Simulated Deposit Formation in Coal-Fired Rotary Kilns for Iron Ore Pellet Production

The Deposit Formation Mechanism in Coal-Fired Rotary Kiln for Iron Ore Pellet Production: A Review

Degradation mechanism of high alumina refractory bricks by reaction with deposits in a rotary kiln for fluxed iron ore pellets production

Formation Mechanism of Deposits in Rotary Kiln during Steelmaking Dust Carbothermic Recycling

Quantitative analysis of minerals of blended coal ash at high temperature and its influence on slagging

STUDY ON MIGRATION AND DEPOSITION BEHAVIOR OF MINERAL SUSTANCES IN COAL BURNING INSIDE THE FURNACE

New Insights on Consolidation Behavior of Fe2O3 in the Fe3O4-CaO-MgO-SiO2 System for Fluxed Pellet Production: Phase Transformations and Morphology Evolution

Research on the Slagging Characteristics of Blended Coals in A Pilot-Scale Furnace

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

The Mineralogy Analysis Of Ash Deposition In Refractory Zones In A W-Flame Boiler

Diffusion and reaction mechanism of limestone and quartz in fluxed iron ore pellet roasting process

Coal ash induced ring formation in a pilot scale rotary kiln for low-grade iron ore direct reduction process: Characterization and mechanism

Research on the Slagging Characteristics of Easy to Slagging Coal in a Pilot Scale Furnace

Study on Deposits Containing Rich Fluorine, Boron, and Ammonium on the Heating Surface of a Flue Gas Cooler in a 300 MW Coal-Fired Boiler

Characteristics of Ash Deposits in A Pulverized Lignite Coal-Fired Boiler and the Mass Flow of Major Ash-Forming Inorganic Elements

Analysis of the melting process of carbon-bearing pellets in iron bath, slag bath and graphite crucible

Investigation of Characteristics and Formation Mechanisms of Deposits on Different Positions in Full-Scale Boiler Burning High Alkali Coal

Dynamic analysis of liquid permeability in the dripping zone of blast furnace and reaction behavior at the slag-coke interface

The Characterization of Sintering Deposit on the Heat-Transfer Surface of CFB Municipal Solid Waste Incinerator