Abstract:In this work, the influence of Mn and Ca doping on the microstructure and mechanical properties of Mg–3Zn, Mg–3Zn-0.5Mn, and Mg–3Zn-0.5Mn-1.2Ca alloys is systematically investigated. The addition of Mn elements is shown to exert no obvious effect on the microstructure of as-cast, as-homogenized, and extruded Mg–3Zn alloys. In contrast, the introduction of Ca into the extruded Mg–3Zn-0.5Mn alloy promotes the formation of nano-sized compounds and enhances grain refinement compared to the other two alloys. The extruded Mg–3Zn-0.5Mn alloy exhibits the higher yield strength (YS, 155 MPa) and ultimate tensile strength (UTS, 183 MPa) but the lower elongation (13%) than the extruded Mg–3Zn alloy (YS of 130 MPa, UTS of 175 MPa, and elongation of 25%). The improved strength of the extruded Mg–3Zn-0.5Mn alloy is mainly attributed to the refined grains, while both the lack of twinning deformation and strong texture result in ductility loss. The most optimal combination of strength and ductility is achieved in an extruded Mg–3Zn-0.5Mn-1.2Ca alloy (YS of 180 MPa, UTS of 250 MPa, and elongation of 26%). This suggests that fine grains and high volume fraction of nano-sized MgZn2 compounds contribute mainly to the strength of Mg–3Zn-0.5Mn-1.2Ca alloy. Although the grain refinement also facilitates the suppression of twinning in the extruded Mg–3Zn-0.5Mn-1.2Ca alloy, the weak texture and fine homogeneous grains are conducive to the high ductility.

Role of Zn addition on the microstructure and tensile property in Mg–Mn–Nd alloys

Simultaneous improvement of strength and ductility by Mn addition in extruded Mg–Gd–Zn alloy

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Effects of Mn Addition on the Microstructures and Mechanical Properties of the Mg-15Gd-1Zn Alloy

Effect of Mn content on the microstructure and mechanical properties of as-extruded Zn-0.2Mg-Mn (wt%) alloys

Effects of Sn and Mn Addition on the Microstructure and Mechanical Properties of As-Extruded Mg–2Al–1Zn Alloys

Effect of Zn on the microstructure evolution of extruded Mg-3Nd (-Zn)-Zr (wt.%) alloys

Microstructure and Mechanical Properties of Extruded Mg–Gd–Y–Zn Alloy with Mn or Zr Addition

Effect of Mn Addition on Microstructure, Texture and Mechanical Properties of Mg–Zn–Ca Alloy

Microstructure and Mechanical Properties of Mg–4.5Zn–xNd (x=0, 1 and 2, Wt%) Alloys

Effect of Nd addition on the microstructure and mechanical properties of extruded Mg-Gd-Zr alloy

Microstructure and Mechanical Properties of Extruded Mg–Zn–Mn–Ca Alloys

Influence of Zn on the microstructure and mechanical properties of Mg-Gd-Zr alloy

Effects of Zn Addition on the Microstructure, Tensile Properties and Formability of As-Extruded Mg-1Sn-0.5Ca Alloy

Study on Microstructure and Tensile Mechanical Properties of As-Extruded Mg-xZn-2.8Nd-0.6Zr-0.6Cd Alloy

Influence of Zn Content on Microstructure and Tensile Properties of Mg–Zn–Y–Nd Alloy

Microstructural Characteristics and Mechanical Properties of Cast Mg–3Nd–3Gd–xZn–0.5Zr Alloys

Microstructure and Mechanical Properties of Extruded Mg-Zn-Nd-Y-Zr-Ca Alloy

Microstructure and mechanical properties of hot-rolled Mg–Zn–Nd–Zr alloys

Effect of Zn content on microstructure, mechanical properties and fracture behavior of Mg-Mn alloy

Microstructure and Mechanical Properties of Mg-7Zn-3Al Alloy with Nd and Y Additions