Abstract:The direct DME synthesis from syngas was studied by using activated carbon-based bifunctional catalytic beds. Two kinds of activated carbons, prepared by physical (by CO 2 partial gasification) and chemical (with phosphoric acid) activation of olive stones, were used as supports for the preparation of the catalysts. The chemically activated carbon presented a considerable amount of thermally and chemically stable surface phosphorus complexes, which played an important role on the catalytic performance of the prepared catalysts. A Zr-loaded P-containing activated carbon presented a relatively high activity, selectivity and stability for the production of DME from methanol and was used as methanol dehydration catalyst. On the other hand, Cu-Zn was loaded on both P-containing and P-free activated carbon supports for the preparation of methanol synthesis catalysts. The presence of surface-phosphorus on the carbon support resulted in a strong metal-support interaction, hindering the catalytic activity for the hydrogenation of CO to methanol. However, the catalyst that did not contain phosphorus showed noticeable activity for this reaction. The physical mixing of the methanol synthesis and methanol dehydration catalysts resulted in the preparation of carbon-based bifunctional catalytic beds, which performed very efficiently in the direct DME synthesis from syngas in a fixed-bed reactor. Different mass ratios of the individual (metallic and acid) catalysts were studied. An acid/metallic catalyst mass ratio of 2 provided the catalytic bed with enough acid sites to promote methanol dehydration to its maximum extent and make the overall product distribution controlled by the methanol synthesis reaction on the metallic phase.

Cu–Mn–Al based catalyst for the direct syngas to dimethyl ether conversion

Direct Synthesis of Dimethyl Ether on Supported Cu-Mn Catalysts

DME Synthesis From CO/H 2 over Cu-Mn/Ă-Al 2 O 3 Catalyst

DME Synthesis From CO/H<sub>2</sub> over Cu-Mn/Ă-Al<sub>2</sub>O<sub>3</sub> Catalyst

Dme Synthesis From Co/H-2 Over Cu-Mn/Gamma-Al2o3 Catalyst

Synthesis of Dimethyl Ether on Supported Cu-Mn Catalysts

The Direct Synthesis of Dimethyl Ether from Syngas over Hybrid Catalysts with Sulfate-Modified Γ-Alumina As Methanol Dehydration Components

Catalysis for One-step Synthesis of Dimethyl Ether from Hydrogenation of CO

Biomass-derived activated carbon catalysts for the direct dimethyl ether synthesis from syngas

The Structure Properties of CuZnAl Slurry Catalysts Prepared by a Complete Liquid-Phase Method and its Catalytic Performance for DME Synthesis from Syngas

Synergistic Effect of Zinc and Manganese in Cu-Mn-Zn/Y Catalyst for Syngas-to-dimethyl Ether

Direct methanol production from mixed methane/H2O/N2O feedstocks over Cu–Fe/Al2O3 catalysts

Single-Step Synthesis of Dimethyl Ether from Biomass-Derived Syngas over Cuo-Zno-Mox (M = Zr, Al, Cr, Ti)/Hzsm-5 Hybrid Catalyst: Effects of Mox

Catalytic performance of CuZnAl slurry catalyst prepared by complete liquid phase technology for direct synthesis DME from syngas

Non‐oxidative conversion of methanol to dimethyl ether, methyl formate and dimethoxymethane over Cu/Hβ catalyst: Tailoring product selectivity

The influence of Mg/Al molar ratio on the performance of CuMgAl-x catalysts for CO2 hydrogenation to methanol

Effect of the Addition of Manganese and Zinc on the Properties of Copper-Based Catalyst for the Synthesis of Syngas to Dimethyl Ether

Optimizing CO 2 Hydrogenation to DME through Tailored Interfacial Interactions: Weakening Synergy in CuZnZr and Al-Modified SBA-15 Catalysts

A novel catalyst for DME synthesis from CO hydrogenation 1. Activity, structure and surface properties

Design and Synthesis of Spherical-Platelike Ternary Copper-Cobalt-manganese Catalysts for Direct Conversion of Syngas to Ethanol and Higher Alcohols