Abstract:Coupled chemical and mechanical phenomena at electrode interfaces largely govern the reversibility and long term stability of lithium ion and lithium metal batteries. A well-known example in lithium ion batteries is the formation of the electrically insulating, ionically conductive, continuous solid electrolyte interface (SEI) on graphitic anodes, which passivates the electrode against further electrochemical reduction of the electrolyte. Unfortunately, this stable passivation does not occur in Si and Li metal anodes. High voltage cathodes are also prone to detrimental interfacial processes, resulting in electrolyte oxidation, gas formation, and transition metal dissolution. In response, a myriad of coating technologies has been developed to mitigate and control these interfacial phenomena and enable next-generation electrodes. These technologies must provide thin, conformal coatings over the entire electrochemically active surface area of the electrode; the coatings must also possess the requisite mechanical properties to accommodate volume dilation due to lithium insertion/extraction. This presentation will describe the development of conformal, compliant polymer thin film coatings for lithium battery electrodes. The polymer thin films are prepared by initiated chemical vapor deposition (iCVD), which provides exquisite control over film composition and morphology by facilitating heterogeneous free-radical polymerization of vinyl monomers with thickness precision on the order of 1 nm. Poly(1,3,5,7-tetravinyl-1,3,5,7-tetramethylcyclotetrasiloxane) (pV4D4) was deposited onto silicon thin film electrodes using iCVD. 25 nm-thick pV4D4 films on Si electrodes improved initial coulombic efficiency by 12.9% and capacity retention over 100 cycles by 64.9% relative to untreated electrodes. PV4D4 coatings also improved rate capabilities, enabling higher lithiation capacity at all current densities. Post-cycling FTIR and XPS showed that pV4D4 inhibited electrolyte reduction and altered the SEI composition, with enrichment in LiF. In another example, thin conformal coatings of perfluorinated polymer were deposited onto battery-grade Cu current collectors to function as an artificial solid electrolyte interface. The effect of the film thickness on Li cycling reversibility was characterized. By galvanostatically cycling Li in an asymmetric Li||Cu cell using 1M LiFSI in a 1:1 (v/v) mixture of dioxolane:dimethoxyethane at 30°C, it was shown that the average coulombic efficiency averaged over 50 cycles increased from 98.36% for bare, untreated Cu to 99.08% for Cu coated with 25 nm of the fluoropolymer. Moreover, the 25 nm coating suppressed interfacial impedance growth on the current collector; the resistance of the coated Cu was 40% lower than the untreated Cu after 100 cycles. The mechanism by which the polymer coating enhances coulombic efficiency and suppresses side reactions will be discussed, along with discussion of the performance in practical anode-free lithium metal batteries.

Non-Electroconductive Polymer Coating on Graphite Mitigating Electrochemical Degradation of PTFE for a Dry-Processed Lithium-Ion Battery Anode

Mitigating PTFE decomposition in ultra thick dry-processed anodes for high energy density lithium-ion batteries

Electrochemical Performance of Dry Processed Graphite Electrode with PTFE Binder for Lithium-Ion Batteries

Removing electrochemical constraints on polytetrafluoroethylene as dry-process binder for high-loading graphite anodes

Revisiting Polytetrafluorethylene Binder for Solvent-Free Lithium-Ion Battery Anode Fabrication

Confluence of ZnO and PTFE Binder for Enhancing Performance of Thin‐Film Lithium‐Ion Batteries

A Fluorinated, Ion-Conducting and Adaptive Supramolecular Polymer Protective Layer for Stabilizing Lithium Metal Anodes

Boosted electrochemical performance of graphite anode enabled by polytetrafluoroethylene-derived F-doping

Phase-Separation-Induced Porous Lithiophilic Polymer Coating for High-Efficiency Lithium Metal Batteries

(Invited) Lithium Battery Interfacial Engineering with Thin Conformal Polymer Coatings

A Solvent-Free Process Enabled by Polytetrafluoroethlyene/Carbon Black Composites for Fabricating Electrodes for Lithium-Ion Batteries with a High Volumetric Energy

Ion Flux Regulation through PTFE Nanospheres Impregnated in Glass Fiber Separators for Long‐Lived Lithium and Sodium Metal Batteries

Unlocking Mechanism of Anion and Cation Interaction on Ion Conduction of Polymer Based Electrolyte in Metal Batteries

The Impact of PTFE:PVDF Ratio on the Fabrication of Free-Standing Electrodes for Solvent-Free Dry Electrodes in Libs

In Situ Hybrid Crosslinking Polymerization of Nanoparticles for Composite Polymer Electrolytes to Achieve Highly‐Stable Solid Lithium–Metal Batteries

Effects of a Thermally Electrochemically Activated β-PVDF Fiber on Suppression of Li Dendrite Growth for Anode-Free Batteries

Design of a Teflon‐Like Anion for Unprecedently Enhanced Lithium Metal Polymer Batteries (Adv. Energy Mater. 15/2023)

Bipolar Polymeric Protective Layer for Dendrite‐Free and Corrosion‐Resistant Lithium Metal Anode in Ethylene Carbonate Electrolyte

Microporous Metal–Organic Framework (MOF)-Based Composite Polymer Electrolyte (CPE) Mitigating Lithium Dendrite Formation in All-Solid-State-Lithium Batteries

Enhanced Electrochemical Performance of Core-Shell Li4ti5o12/Pth As Advanced Anode for Rechargeable Lithium-Ion Batteries

First‐Principles Study on Polymer Electrolyte Interface Engineering for Lithium Metal Anodes