Abstract:Recent advances in additive manufacturing (AM) have enabled the fabrication of functionally graded porous biomaterials (FGPBs) for application as orthopedic implants and bone substitutes. Here, we present a step-wise topological design of FGPB based on diamond unit cells to mimic the structure of the femoral diaphysis. The FGPB was manufactured from Ti-6Al-4V powder using the selective laser melting (SLM) technique. The morphological parameters, permeability and mechanical properties of FGPB samples were measured and compared with those of the biomaterials with uniform porous structures based on the same type of the unit cell. The FGPB exhibited a low density (1.9 g/cm3), a moderate Young's modulus (10.44 GPa), a high yield stress (170.6 MPa), a high maximum stress (201 MPa) and favorable ductility, being superior to the biomaterials with uniform porous structures in comprehensive mechanical properties. In addition, digital image correlation (DIC) and finite element (FE) simulation were used to unravel the mechanisms governing the deformation and yielding behavior of these biomaterials particularly at the strut junctions. Both DIC and FE simulations confirmed that the deformation and yielding of the FGPB occurred largely in the load-bearing layers but not at the interfaces between layers. Defect-coupled FE models based on solid elements provided further insights into the mechanical responses of the FGPB to compressive loads at both macro- and micro-scales. With the defect-coupled representative volume element model for the FGPB, the Young's modulus and yield stress of the FGPBs were predicted with less than 2% deviations from the experimental data. The study clearly demonstrated the capabilities of combined experimental and computational methods to resolve the uncertainties of the mechanical behavior of FGPBs, which would open up the possibilities of applying various porosity variation strategies for the design of biomimetic AM porous biomaterials. STATEMENT OF SIGNIFICANCE: Functionally graded bone scaffolds significantly promote the recovery of segmental bone defect. In the present study, we present a step-wise topological design of functionally graded porous biomaterial (FGPB) to mimic the structure of the femoral diaphysis. The Ti-6Al-4V FGPB exhibited a superior combination of low density, moderate Young's modulus, high yield stress and maximum stress as well as favorable ductility. The biomechanical performance of FGPB was studied in both macro and micro perspectives. The defect-coupled model revealed the significant yielding in the load-bearing parts and the Young's modulus and yield stress of the FGPBs were predicted with less than 2% deviations from the experimental data. The superiority of combined experimental and computational methods has been confirmed.

Additively-manufactured gradient porous bio-scaffolds: Permeability, cytocompatibility and mechanical properties

3D-Printed Bioceramic Scaffolds with High Strength and High Precision

3D Printing Novel Porous Granule-Type Bioceramics Via Magnesium Tuning Biological Performances Beneficial for Implantation and Clinical Translation

3D Printed High-Strength Bioceramic Dome Scaffolds with Controllable Biodegradation for Guided Bone Regeneration

Selective laser sintered bio-inspired silicon-wollastonite scaffolds for bone tissue engineering

Influence of structural parameters of 3D-printed triply periodic minimal surface gyroid porous scaffolds on compression performance, cell response, and bone regeneration

Biomechanical Influence of Structural Variation Strategies on Functionally Graded Scaffolds Constructed with Triply Periodic Minimal Surface

Mechanical and degradation properties of triply periodic minimal surface (TPMS) hydroxyapatite & akermanite scaffolds with functional gradient structure

Design of a Haversian System-Like Gradient Porous Scaffold Based on Triply Periodic Minimal Surfaces for Promoting Bone Regeneration

Biomechanical Effects of 3D-Printed Bioceramic Scaffolds With Porous Gradient Structures on the Regeneration of Alveolar Bone Defect: A Comprehensive Study

Full compression response of FG-based scaffolds with varying porosity via an effective numerical scheme

Parametric design and performance study of continuous gradient triply periodic minimal surface bone scaffold

Additive manufacturing of Bio-inspired ceramic bone Scaffolds: Structural Design, mechanical properties and biocompatibility

Analysis of Mechanical Properties and Permeability of Trabecular-Like Porous Scaffold by Additive Manufacturing

Continuous functionally graded porous titanium scaffolds manufactured by selective laser melting for bone implants

Effect of Porosity and Pore Shape on the Mechanical and Biological Properties of Additively Manufactured Bone Scaffolds.

Effect of Porosity and Pore Shapes on the Mechanical and Biological Properties of Additively Manufactured Bone Scaffolds

Topological design, permeability and mechanical behavior of additively manufactured functionally graded porous metallic biomaterials

Additively-manufactured PEEK/HA porous scaffolds with highly-controllable mechanical properties and excellent biocompatibility

Additively Manufactured Zn‐2Mg Alloy Porous Scaffolds with Customizable Biodegradable Performance and Enhanced Osteogenic Ability

Advancements in gradient bone scaffolds: enhancing bone regeneration in the treatment of various bone disorders