Abstract:Recent advances in additive manufacturing (AM) have enabled the fabrication of functionally graded porous biomaterials (FGPBs) for application as orthopedic implants and bone substitutes. Here, we present a step-wise topological design of FGPB based on diamond unit cells to mimic the structure of the femoral diaphysis. The FGPB was manufactured from Ti-6Al-4V powder using the selective laser melting (SLM) technique. The morphological parameters, permeability and mechanical properties of FGPB samples were measured and compared with those of the biomaterials with uniform porous structures based on the same type of the unit cell. The FGPB exhibited a low density (1.9 g/cm3), a moderate Young's modulus (10.44 GPa), a high yield stress (170.6 MPa), a high maximum stress (201 MPa) and favorable ductility, being superior to the biomaterials with uniform porous structures in comprehensive mechanical properties. In addition, digital image correlation (DIC) and finite element (FE) simulation were used to unravel the mechanisms governing the deformation and yielding behavior of these biomaterials particularly at the strut junctions. Both DIC and FE simulations confirmed that the deformation and yielding of the FGPB occurred largely in the load-bearing layers but not at the interfaces between layers. Defect-coupled FE models based on solid elements provided further insights into the mechanical responses of the FGPB to compressive loads at both macro- and micro-scales. With the defect-coupled representative volume element model for the FGPB, the Young's modulus and yield stress of the FGPBs were predicted with less than 2% deviations from the experimental data. The study clearly demonstrated the capabilities of combined experimental and computational methods to resolve the uncertainties of the mechanical behavior of FGPBs, which would open up the possibilities of applying various porosity variation strategies for the design of biomimetic AM porous biomaterials. STATEMENT OF SIGNIFICANCE: Functionally graded bone scaffolds significantly promote the recovery of segmental bone defect. In the present study, we present a step-wise topological design of functionally graded porous biomaterial (FGPB) to mimic the structure of the femoral diaphysis. The Ti-6Al-4V FGPB exhibited a superior combination of low density, moderate Young's modulus, high yield stress and maximum stress as well as favorable ductility. The biomechanical performance of FGPB was studied in both macro and micro perspectives. The defect-coupled model revealed the significant yielding in the load-bearing parts and the Young's modulus and yield stress of the FGPBs were predicted with less than 2% deviations from the experimental data. The superiority of combined experimental and computational methods has been confirmed.

Biomechanical Influence of Structural Variation Strategies on Functionally Graded Scaffolds Constructed with Triply Periodic Minimal Surface

Revealing the Apparent and Local Mechanical Properties of Heterogeneous Lattice: a Multi-Scale Study of Functionally Graded Scaffold

Topological design, permeability and mechanical behavior of additively manufactured functionally graded porous metallic biomaterials

Effect of porosity variation strategy on the performance of functionally graded Ti-6Al-4V scaffolds for bone tissue engineering

Parametric design and performance study of continuous gradient triply periodic minimal surface bone scaffold

Full compression response of FG-based scaffolds with varying porosity via an effective numerical scheme

3D-Printed Ti6Al4V Scaffolds with Graded Triply Periodic Minimal Surface Structure for Bone Tissue Engineering

Mechanical Characterisation and Numerical Modelling of TPMS-Based Gyroid and Diamond Ti6Al4V Scaffolds for Bone Implants: An Integrated Approach for Translational Consideration

Multi-parameter design of triply periodic minimal surface scaffolds: from geometry optimization to biomechanical simulation

Design and Analysis of Biomedical Scaffolds Using TPMS-Based Porous Structures Inspired from Additive Manufacturing

Mechanical and degradation properties of triply periodic minimal surface (TPMS) hydroxyapatite & akermanite scaffolds with functional gradient structure

Design Exploration of Staggered Hybrid Minimal Surface Magnesium Alloy Bone Scaffolds

Additively-manufactured gradient porous bio-scaffolds: Permeability, cytocompatibility and mechanical properties

Effects of modeling strategies of triply periodic minimal surface on the mechanical properties and permeability of biomedical TC4 porous scaffolds

Mechanical properties of triply periodic minimal surface (TPMS) scaffolds: considering the influence of spatial angle and surface curvature

Influence of structural parameters of 3D-printed triply periodic minimal surface gyroid porous scaffolds on compression performance, cell response, and bone regeneration

Continuous functionally graded porous titanium scaffolds manufactured by selective laser melting for bone implants

Design procedure for triply periodic minimal surface based biomimetic scaffolds

Fatigue behavior of As-built selective laser melted titanium scaffolds with sheet-based gyroid microarchitecture for bone tissue engineering

The design of Ti6Al4V Primitive surface structure with symmetrical gradient of pore size in biomimetic bone scaffold

Regulated Multi-Scale Mechanical Performance of Functionally Graded Lattice Materials Based on Multiple Bioinspired Patterns