Abstract:Heavy metal-based vehicle caused increase in fuel consumption, which creates pollution in the environment; thus, scientists across the nation researched to produce light weight, cost-effective, easy degradable, corrosive resistant composite material. Due to such features present in the composite material, the present research aims to examine the impact of alkali-silane treatment on the time-dependent and machining behavior of composites. Further, the alkali treatment and silane treatment on fiber and filler particle are carried out to provide even dispersion of filler particle and better reinforcement and interfacial bonding adhesion to the composite material, which makes a novelty to this study. The obtained fiber and filler particle were reinforced to matrix by using hand layup method and subsequently cured. This prepared composite material's strength is analyzed as per the ASTM standards. The results indicate that the inclusion of surface modified corn-fiber reinforced EF composite shows stronger interfacial adhesion, which implies loss factor of 42.8% lower than neat epoxy. Similarly, reinforcing corn husk fiber increases the energy release rate by 2500% and the fracture toughness by 156.47% when compared to pure epoxy composite. Further, the inclusion of biosilica particle of 2.0 vol.% exhibited the highest storage modulus of 5.69 GPa and the lowest loss factor of 0.32. This demonstrates the beneficial effect of combining alkali and silane treatment on corn fiber and filler particle. The epoxy composite (EFP3) of chemically treated fiber 30 vol.% and 2 vol.% of biosilica reinforcement exhibits a higher fatigue life cycle, fracture toughness, and energy release rate of 30,546, 26.5 MPa√m, and 0.86 MJ/m 2 , respectively. Similarly, the composite designation EFP3 has the lowest contact angle of 78°, indicating the preserved hydrophobicity. A drilling study has shown that using a 4-mm drill bit and 8-mm drill bit. The resultant of the drilling studies concludes that the use of 2.0 vol.% biosilica reduced the occurrence of fiber pull-out while drilling. Owing to such improved strength properties, light weight, corrosive resistant features in the biocomposite are applied in industries such as automotive, sporting goods, food and drug packaging, aerospace, and other technical applications that require strong load-bearing capacity, etc.

Experimental evaluation and prediction on drilling of Corchorus olitorius filler-based composite

A New Strategy of Carbon Fiber Reinforced Plastic Drilling Evaluation Using Thermal Measurement

Machinability investigation of natural fibers reinforced polymer matrix composite under drilling: Leveraging machine learning in bioengineering applications

Experimental investigation on mechanical performance and drilling behavior of hybrid polymer composites through statistical and machine learning approach

Effect of drilling process parameters on agro-waste-based polymer composites reinforced with banana fiber and coconut shell filler

An integrated CRITIC-COPRAS approach for multi-response optimization on AWJM of hybrid filler–reinforced polymer composite and its surface integrity

A Comparative Analysis of the Tribological Performance of Coir, Bamboo and Wood Filler Reinforced Polymer Composites

Mechanical, tribological and modal characteristics of eco-friendly coir/sugarcane fillers reinforced polymer composites

Impact of process parameters in drilling of glass epoxy composite with clam shell and cenosphere filler: A comparative analysis

A Comprehensive Study on the Optimization of Drilling Performance in Hybrid Nano-Composites and Neat CFRP Composites Using Statistical and Machine Learning Approaches

Effect of Drilling Force on Delamination of Abaca/Kenaf/Carbon Fiber Reinforced Hybrid Composite

Drilling characteristics and properties analysis of fiber reinforced polymer composites: A comprehensive review

Machine learning strategy to improve impact strength for PP/cellulose composites via selection of biomass fillers

Investigation on carbon fiber-reinforced polymer combined with graphene nanoparticles subjected to drilling operation using response surface methodology and non-dominated sorting genetic algorithm-II

Delamination and surface roughness analysis of jute/polyester composites using response surface methodology: Consequence of sodium bicarbonate treatment

Valorisation of corn waste as fiber, biosilica, and their epoxy composites: fatigue, fracture toughness, water absorption, and drilling properties

Influence of brown algae filler and process parameters on the surface roughness and MRR of jute fiber polymeric composite machined by abrasive water jet

Machinablity of Hybrid Natural Fiber Composite with and without Filler as Reinforcement

Optimization of Drilling Parameters on Delamination and Burr Formation in Drilling of Neat CFRP and Hybrid CFRP Nano-Composites

Assessment and analysis of drilling-induced damage in jute/palm date fiber-reinforced polyester hybrid composite

Experimental evaluation of physicomechanical, tribological and optimality circumstances for Corchorus olitorius particle‐based composites