Abstract:Abrasive water jet processing of CARALL composites with various fiber orientations. Carbon Fiber Reinforced Aluminum Laminated (CARALL) composites are widely used in aircraft structures due to their ability to be produced in different shapes with desired properties and their high impact resistance properties. As with other layered composite materials, processing of CARALL composites by conventional manufacturing methods results in many damage mechanisms such as fiber breakage, deformation in the hole region, stress concentration, resin‐fiber separation and microcracks. One of the modern manufacturing methods, Abrasive Water Jet (AWJ), is a processing method in which the material is removed by abrasion and almost any material can be cut without thermal degradation. There are no experimental studies in the literature on the drilling of CARALL composites by modern manufacturing methods. The aim of this study is to investigate the impact of machining parameters on the output variables (kerf taper angle (K), roundness error (Re) and material removal rate (MRR)) as well as the effect of fiber orientation on the drilling of CARALL composites with different fiber orientations on an AWJ machine. PROMETHEE‐GAIA weighted by Entropy Weighting Method were used to ascertain the optimum levels of control factors. CARALL composites with different fiber orientations were drilled with an 8 mm diameter AWJ with three different water pressures, three different nozzle feed rates. With PROMETHEE‐GAIA multi‐criteria optimization method, the optimum levels of the factors that provide both minimum Re and K values and maximum MRR value were obtained with twill woven material, 1680 mm/min feed rate and 1680 bar water pressure. Highlights CARALL composite materials with two different fiber orientations (twill weave and UD) were used. CARALL composite materials were drilled at different machining parameters. Abrasive water jet was used in drilling experiments. Optimum drilling parameters were determined to achieve minimum roundness error, minimum kerf angle and maximum material removal rate. PROMETHEE‐GAIA was used as a multi‐criteria decision‐making method.

Influence of brown algae filler and process parameters on the surface roughness and MRR of jute fiber polymeric composite machined by abrasive water jet

Study on Machining Quality in Abrasive Water Jet Machining of Jute-Polymer Composite and Optimization of Process Parameters through Grey Relational Analysis

Abrasive water jet machining of coir fiber reinforced epoxy composites: a review

An integrated CRITIC-COPRAS approach for multi-response optimization on AWJM of hybrid filler–reinforced polymer composite and its surface integrity

Simultaneous optimization of process parameters during abrasive water jet machining on glass fibre reinforced polymer

Experimental study on abrasive water jet machining of WCFC reinforced flax/wire mesh/hemp composite

Composite Cutting with Abrasive Water Jet

Abrasive Jet Machining of Incense Stick Ash Filled Luffa-Human Hair Based Sustainable Bio-composite Using Taguchi Based GRA

Delamination and surface roughness analysis of jute/polyester composites using response surface methodology: Consequence of sodium bicarbonate treatment

Experimental investigation on abrasive water jet machining of neem wood plastic composite

Investigation of Abrasive water jet machining parameters of Bismaleimide composites

Abrasive water jet machining of glass fibre reinforced polymer composite: experimental investigation, modelling and optimization

Evaluating the optimum abrasive water jet machinability for CARALL composites with various fiber orientations

Integrating response surface methodology and machine learning for analyzing the unconventional machining properties of hybrid fiber‐reinforced composites

Evaluation of Mechanical and Water Absorption Behaviors of Jute/Carbon Fiber Reinforced Polyester Hybrid Composites

Effects of machining parameters on surface quality of composites reinforced with natural fibers

Experimental evaluation and prediction on drilling of Corchorus olitorius filler-based composite

Effect of Abrasive Water Jet Parameters on the Drilling of Aluminum Foam Sandwiched with Glass Fiber Polymer Composites

Influence of Load and Sliding Velocity on Abrasive Wear of Polyester Composites Reinforced with Bio-Particulates as Filler Material

Insight to the influence of alkali treatment on mechanical and tribological properties of a novel carbon/jute hybrid porcine filled polyester composite

Optimization of AWJ parameters for improved material removal and hole geometry in drilling of Glass Fiber/Aluminum mesh epoxy hybrid composites