Abstract:Increasing interest in hydrogen-powered fuel cells for electric energy generation led to the identification of serious limitations of state-of-the-art technologies. In particular, low-temperature fuel cell with a proton-exchange membrane (LT-PEM FC), which is widely considered as an optimal type for mobility, is reaching its technological limits. This is due to its operating temperature up to 90 °C, defined by properties of perfluorinated, sulfonated membranes used as PEM, requiring liquid water for ensuring their ionic conductivity. In the case of heavy duty applications, high-power LT-PEMFC stacks suffer from local overheating, which is currently solved by intensive cooling. Ineffective heat-exchange and necessity of water regime control lead to limitations in total energy utilization. Such problem can be solved by increasing operating temperature up to 180 °C, which is suitable for heat cogeneration. This requires application of appropriate PEM conducting even at an elevated temperature. Current state-of-the-art high-temperature PEM fuel cells (HT-PEM FCs) utilize PEMs based on polymer doped with phosphoric acid. Polymers, such as polybenzimidazole or pyridine aromatic polyether, act as a matrix and a bonding agent for the phosphoric acid dopant. Such PEMs can operate within the temperature range of 120 to 180 °C. In terms of the catalyst, HT-PEM FCs use Pt-based, nanoparticle catalysts on carbon support as in LT-PEM FCs. However, due to the mobile nature of phosphoric acid, which is responsible for pronounced catalyst degradation, poisoning as well as local catalytic layer flooding, Pt loading used in HT-PEM FCs is within an order of magnitude higher than in LT-PEM FCs. Due to its high operating temperature, HT-PEM FC technology offers numerous advantages, such as heat and electric energy cogeneration, simple water regime and, due to improved tolerance to catalyst poisons like CO, the possibility of utilization of contaminated H 2 produced from fossil fuels and biomass. However, degradation of components, in particular the catalyst and the membrane, remain the main bottlenecks for wide HT-PEM FC commercialization. With respect to the latest advances in technology, two critical aspects were identified. Firstly, the necessity of new catalysts immobilized on durable supports, with improved stability, activity and resistance against poisoning by phosphate anions. Secondly, membrane with improved fixation of phosphoric acid and greater durability. A special case of the membrane degradation is the reduction of phosphoric acid, by hydrogen or at low potentials on the anode, to phosphorous acid. This compound can poison the anode catalyst, incorporate into the membrane as well as oxidize on the cathode to phosphoric acid, completing dopant lifecycle. Nevertheless, the exact impact of phosphorous acid on HT-PEM FC performance is still not fully understood. Accordingly, the study had two major goals. A first one was to investigate the performance and degradation of Pt-based alloy catalyst on graphene-type support using thin-film modified rotating disc electrode, half-cell and single cell setups. All experiments have been performed at HT-PEM FC relevant conditions, i.e. in concentrated phosphoric acid electrolyte within temperature range of 120 to 180 °C. On the other hand, the second one goal investigated the influence of the dopant composition in terms of phosphorous acid addition to phosphoric acid electrolyte on the activity of the catalyst. Performance of experimental catalysts based on Pt-Co on various supports, including carbon black and graphene was compared to commercial Pt/C catalyst. Experimental catalysts exhibited superior activity for oxygen reduction. The overall performance of single cells with experimental catalyst on the cathode was better than the one with the commercial catalyst, with best results obtained for the graphene supported Pt-Co. The impact of phosphorous acid on oxygen reduction on commercial Pt/C catalyst was significant, due to simultaneous oxidation of acid and reduction of oxygen, as confirmed using rotating disc electrode and half-cell setups. Using the addition of phosphorous acid after single cell break-in on the cathode, the anode or both electrodes at once, it was determined that after stabilization the performance improved. Electrochemical impedance spectroscopy showed that addition of phosphorous acid decreases cell Ohmic resistance, but the comparative I-U curves and CO stripping analysis performed on cathode indicated significant decrease of available Pt surface. This reflects the ambivalent influence of phosphorous acid on HT-PEM FC. This study was supported by the Grant Agency of the Czech Republic under project No. 22-23668K.

Temperature Influence on the Synthesis of Pt/C Catalysts for Polymer Electrolyte Membrane Fuel Cells

Effect of Solvent Ratio (Ethylene Glycol/Water) in the Synthesis of Pt/C Cathode Catalysts on PEM Fuel Cell Performance

Alkaline Water-Assisted Polyol Synthesis of Pt/Vulcan PEMFC Cathode Electrocatalysts

Mitigation of Performance Degradation of Cathodes for Polymer Electrolyte Membrane Fuel Cells

(Invited) Controlled Synthesis of the Ultra-Low-Platinum Electrocatalysts for High-Performance Polymer Electrolyte Membrane Fuel Cell (PEMFC) Cathode

Synthesis of a Pt/C Electrocatalyst from a User-Friendly Pt Precursor (Ammonium Hexachloroplatinate) through Microwave-Assisted Polyol Synthesis

Improvement of fuel cell performances through the enhanced dispersion of the PTFE binder in electrodes for use in high temperature polymer electrolyte membrane fuel cells

Catalyst Development for High‐Temperature Polymer Electrolyte Membrane Fuel Cell (HT‐PEMFC) Applications

Instability of Pt ∕ C Electrocatalysts in Proton Exchange Membrane Fuel Cells A Mechanistic Investigation

Controlled Synthesis of Ptm (m=transition Metal) Alloy Nanostructures Via Organic Solvents As High-Performance Oxygen Reduction Reaction Electrocatalysts

Optimization of a catalyst layer with a high-utilization gradient Pt distribution for polymer electrolyte membrane fuel cells

Effect of Low and Sub-Freezing Temperature on the PEFC Performance of Unsupported Pt-Ni Aerogel Cathode Catalyst Layers

The influences of catalyst combination on the high temperature proton exchange membrane fuel cell

Optimizing design of catalyst layer structure with carbon-supported platinum weight ratio mixing method for proton exchange membrane fuel cells

Impact of the Catalyst Type and Dopant Composition on the Performance of High-Temperature PEM Fuel Cell

The Electrocatalysis of Oxygen Reduction on Platinum and Its Alloys

High-temperature annealing improves Pt utilization of proton exchange membrane fuel cell cathode catalysts

Incorporating ALD Based Pt Alloy Catalysts into Gas Diffusion Electrodes for Proton Exchange Membrane Fuel Cells

Effect of Catalyst Pore Size on the Performance of Non‐Precious Fe/N/C‐Based Electrocatalysts for High‐Temperature Polymer Electrolyte Membrane Fuel Cells

Modulating the Reactivity of Pt-based Catalysts for PEMFC: A First Principles Study

A novel approach to pulsed laser deposition of platinum catalyst on carbon particles for use in polymer electrolyte membrane fuel cells