Abstract:Solar cells have attracted much attention since they can convert solar energy directly into electricity, and have been widely utilized in manufacturing industry and people's daily life. Although the power conversion efficiency (PCE) of single-junction solar cells has gradually improved in recent years, its maximum efficiency is restricted by the Shockley-Queisser (SQ) limit of single-junction solar cells. To exceed the SQ limit and further obtain high efficiency solar cells, researchers have proposed the concept of tandem solar cells. In this work, a systematic theoretical study of chalcopyrite CuGaSe 2 /CuInSe 2 tandem solar cells was carried out by combining first-principle calculations and SCAPS-1D device simulations. Firstly, the electronic structure, defect properties and corresponding macroscopic performance parameters of CuGaSe 2 (CGS) were obtained by first-principles calculations, which were adopted as input parameters for subsequent device simulations of CGS solar cells. Subsequently, the simulations of single-junction CGS and CuInSe 2 (CIS) solar cells were carried out using SCAPS-1D software, respectively. The simulation results for the single junction CIS solar cells are in good agreement with the experimental values. For single-junction CGS cells, the device simulations revealed that CGS single-junction solar cells had the highest short-circuit current (J sc ) and PCE at the growth condition of Cu-rich, Ga-rich and Se-poor chemical growth condition. Further optimization found that the open-circuit voltage (V oc ) and PCE of CGS solar cells can be improved by replacing the electron transport layer (ETL) with ZnSe after the devices with the highest short-circuit current (J sc ). Finally, after the optimized CGS and CIS solar cells were connected in series with two-terminal (2T) monolithic tandem solar cell, the device simulation results show that under the growth temperature of 700 K and the growth environment of Cu-rich, Ga-rich, and Se-poor, with ZnSe as the ETL, the CGS thickness of 2000 nm and the CIS thickness of 1336 nm, the PCE of 2T monolithic CGS/CIS tandem solar cell can reach 28.91 %, which is higher than the recorded efficiency of the current single-junction solar cells, and shows a good application prospect.

Numerical simulations of novel multi- chalcogenide CuAgBeSnSe4 based thin film solar cell with over 24% efficiency using SCAPS-1D

Numerical Investigation of CuSbS2Thin Film Solar Cell using SCAPS-1D: Enhancement of Efficiency on Experimental Films by Defect Studies

Improving the Performance of Cu2ZnSn(S,Se)4 Thin Film Solar Cells by SCAPS Simulation

Modeling and optimization of numerical studies on CuSbS 2 thin film solar cell with ∼ 15% efficiency

Simulation studies of CZT(S,Se) single and tandem junction solar cells towards possibilities for higher efficiencies up to 22%

A computational study for understanding the effect of various parameters on the performance of three different CI(G)Se-based thin film solar cells

Top cell design and optimization of all-chalcopyrite CuGaSe 2 /CuInSe 2 two-terminal tandem solar cells: first-principles calculations and device simulations

Numerical simulation of Sb2Se3-based solar cells

A Numerical Simulation for Efficiency Enhancement of CZTS Based Thin Film Solar Cell Using SCAPS-1D

Numerical modeling of CuSbSe2-based dual-heterojunction thin film solar cell with CGS back surface layer

Thin-Film Solar Cells Based on Selenized CuSbS2 Absorber

Performance Prediction of Chalcopyrite-Based Dual-Junction Tandem Solar Cells

Dual-Absorber Solar Cell Design and Simulation Based on Sb2Se3 and CZTGSe for High-Efficiency Solar Cells

SCAPS study on the effect of various hole transport layer on highly efficient 31.86% eco-friendly CZTS based solar cell

Elucidating the Potential Strategies for Performance Improvement of CBTSSe‐Based Solar Cells: A Pathway Toward 20% Efficiency

Numerical simulation on an efficient n-CdS/p-ZnSnN2/p+-Cu2SnS3/p++- CuGaSe2 thin film solar cell

Achievable efficiency improvement of Sb2Se3 thin-film solar cells through interface engineering

Toward High Efficient Cu2 ZnSn(Sx ,Se1- x )4 Solar Cells: Break the Limitations of VOC and FF

Numerical study of copper antimony sulphide (CuSbS2) solar cell by SCAPS-1D

Analysis of optical and electrical properties in CZTSSe thin film solar cells through the 2d theoretical modeling

Synergistic Effect of Ag, Sb Dual‐Cation Substitution on Cu2ZnSn (S, Se)4 High‐Efficiency Solar Cells