Abstract:Fluidic and tendon driven actuators are widely applied in soft robotic hand design. Fluidic actuated soft robotic hands are highly compliant and can adapt to various objects. Tendon driven soft robotic hands are easier to control and have high dexterity and large force output, however, they are less compliant than fluidic actuated ones. Most robotic hands are designed with only one actuation method. Combining both actuation methods can tap the advantages and make up each other's limitations but at the expense of more complicated design and control. In this research, we propose a simple dual-mode actuator that provides both fluidic and tendon actuation. The two actuation modes are achieved simultaneously by twisting an elastic tube filled with gas, liquid, or even a combination. The soft robotic finger, designed as a fluidic elastomer actuator (FEA), is actuated by the fluid displaced from tube twisting, as well as by the tendon due to tube contraction in twisting. The tendon drives a compliant metacarpophalangeal (MCP) joint of the finger in order to provide a large bending angle and bending force to finger. Compared to an FEA soft finger, the proposed design can effectively increase the bending angle up to 150 (from 170 degrees to 260 degrees), and the blocking force up to 134 (from 3.2N to 4.3N). A soft robotic hand prototype with dual-mode actuators design is made for various grasping demonstrations.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is the limitations of the single - drive mode (fluid - driven or tendon - driven) in the existing soft - robot finger designs. Specifically: 1. Soft - robot fingers driven by fluid have a high degree of compliance and adaptability and can adapt well to objects of different shapes and sizes. However, they usually need to be connected to a complex pneumatic system, which limits their use in independent applications. 2. Soft - robot fingers driven by tendon are simpler to control, have a larger range of motion, and are more likely to achieve a cable - free design, but their compliance and adaptability are not as good as those of fluid - driven designs. To overcome these limitations, the paper proposes a dual - mode actuator, which combines the advantages of fluid - driven and tendon - driven methods, aiming to increase the bending angle and bending force of soft - robot fingers while maintaining high compliance and adaptability. ### Main features of the dual - mode actuator: 1. **Simplified design**: Only one motor is required to achieve two driving effects, reducing the complexity of electromechanical design. 2. **Simple control**: By controlling the rotation angle and speed of the motor, the bending angle and speed of the finger can be controlled, simplifying the control strategy. 3. **Flexible fluid selection**: The fluid in the tube can be gas, liquid, or a mixture of the two. Adjusting the fluid ratio according to application requirements can change the performance of the actuator. ### Experimental verification: The paper verifies the effectiveness of the dual - mode actuator through experiments: - **Bending angle**: The experimental results show that compared with soft fingers driven by a single - fluid, the dual - mode actuator can significantly increase the bending angle of the finger, up to 150% (from 170 degrees to 260 degrees). - **Bending force**: The experiment also measured the bending force (blocking force) of the finger. The results show that the maximum bending force of the dual - mode actuator can reach 4.3N, which is about 134% higher than that of the single - fluid - driven finger (3.2N). ### Application prospects: The paper shows a prototype of a soft - robot hand designed using the dual - mode actuator and conducts various grasping demonstrations, proving the effectiveness and potential of this design in practical applications. By combining the advantages of fluid - driven and tendon - driven methods, the dual - mode actuator provides a new solution for the design of soft - robot fingers and is expected to play an important role in future robot applications.

A Dual-Mode Actuator for Soft Robotic Hand

Design and Control of an Electrohydraulic Soft Actuator System for Robotic Grippers

Design and Simulation Experiment of Rigid-Flexible Soft Humanoid Finger

Finger Flexion and Extension Driven by a Single Motor in Robotic Glove Design

Untethered Multimode Fluidic Actuation: A New Approach to Soft and Compliant Robotics

A multi-jointed underactuated robot hand with fluid-driven stretchable tubes

Design of Humanoid Robotic Hand Based on Link Underactuation

A finger-inspired pneumatic network actuator based on rigid-flexible coupling structure for soft robotic grippers

A Flexible Self-Adaptive Underactuated Hand With Series Passive Joints

Design Principle of a Dual-Actuated Robotic Hand With Anthropomorphic Self-Adaptive Grasping and Dexterous Manipulation Abilities

Soft Robotic Finger with Energy-Coupled Quadrastability

A Soft-Rigid Hybrid Gripper With Lateral Compliance and Dexterous In-Hand Manipulation

The Indirect Style Under-Actuated Robotic Finger With Tendon-Slider Mechanisms

Bioinspired Multimodal Multipose Hybrid Fingers for Wide-Range Force, Compliant, and Stable Grasping

Double-Source Fluid Bending And Side-Swing Compound Multi-Joint Finger

A Novel Design of Soft Robotic Hand with a Human-inspired Soft Palm for Dexterous Grasping

All-Fabric Bi-directional Actuators for Multi-joint Assistance of Upper Limb

CATCH-919 Hand: Design of a 9-actuator 19-DOF Anthropomorphic Robotic Hand

Tactile SoftHand-A: 3D-Printed, Tactile, Highly-underactuated, Anthropomorphic Robot Hand with an Antagonistic Tendon Mechanism

Towards higher load capacity: innovative design of a robotic hand with soft jointed structure

Soft robotic hand with finger-bending/friction-reduction switching mechanism through 1-degree-of-freedom flow control