Abstract:In this paper, the effect of Si content on the microstructure and mechanical properties of the Al–1.2Mg– x Si–1.2Cu–0.6Mn cast alloy was investigated. The study aimed to explore the optimal addition of Si element to improve the comprehensive properties of alloys. The microstructure, phase composition and fracture morphology of the alloy were determined through OM, SEM, EBSD and XRD analysis. The Si content in the alloy ranged from 0.48 to 2.4 wt.%. With the increase of Si content, the number of strengthening phases increases, which improves the comprehensive properties of the alloy. When the Si content is 0.8 wt.%, the eutectic Mg 2 Si transforms from rod-shaped to larger block shaped, and the formation of coarse Mg 2 Si phase limits the elongation of the alloy. When the Si content is 2.4 wt.%, fine Al 2 Cu phases are present in this alloy and coexist with Al(Fe,Mn)Si phases, while an increase in the Si content appears as partially accompanied by an incipient crystalline Si phase around the Al(Fe,Mn)Si phase. The alloy exhibits a maximum tensile strength, yield strength and elongation of 198.2 MPa, 101.2 MPa and 4.96%, respectively, with a hardness of 80.94 Hv. It consists of five alloy phases, mainly α-Al, Mg 2 Si, Al(Fe, Mn)Si eutectic phase, Q-AlCuMgSi eutectic phase and the beginning crystalline silicon phase formed due to the increased Si content. The Si content can improve alloy strength, but there is some damage to the toughness of the alloy. Higher silicon alloy content results in the formation of fine Al 2 Cu eutectic. This result makes it possible to achieve a higher level of strength with a reduced loss of ductility in the alloy.

The effect of the α phase on the elastic properties of Si3N4

Effects of Atomic Ratio on the Mechanical Properties of Amorphous Silicon Carbon Nitride

Coefficient of thermal expansion and biaxial Young's modulus in Si-rich silicon nitride thin films

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

The Structural, Elastic And Thermodynamic Properties Of Intermetallic Phases In Mg-Sn-Si-Ca(Sr) Alloys: A First-Principles Study

Simulation on the Effect of Porosity in the Elastic Modulus of SiC Particle Reinforced Al Matrix Composites

Effects of Si/Al ratio on structure, modulus of elasticity, and density in N-A-S-H geopolymer: a molecular dynamics simulation based on novel macromolecular model

Effect of Initial Phase Composition on the Phase Composition, Microstructure, and Mechanical Properties of Si3N4 Ceramics

Effect of Si on Phase Equilibria, Mechanical Properties and Tribological Behaviour of Al-Cu Alloy

Density modified structure and mechanical properties of amorphous Si2BC3N by ab‐initio molecular dynamics calculations

Effect of Impurities MgO, CaO, Al2O3, AlN and Al on Α/β Ratio in Combustion Synthesis of Α-Si3n4

Effects of in situ Mg-Sialon and β-Sialon on the microstructure and properties of MgAl2O4-SiC composites

Topology of Charge Density and Elastic Anisotropy of Ti3sic2 Polymorphs

The Analysis of Mechanical Properties of Al-Si Alloys by Molecular Dynamics Simulation and Nanoindentation Method

On the Hardness and Elastic Modulus of Phases in SiC-Reinforced Al Composite: Role of La and Ce Addition

Micromechanics-based thermal expansion characterization of SiC nanoparticle-reinforced metal matrix nanocomposites

The Relationship Between Structural Features and Local Mechanical Properties of a Fine-Grained Matrix in Refractory Ceramic Materials. SiO2 Ceramics Case Study

Compressibility And Thermal Expansion Of Cubic Silicon Nitride

Strengthening mechanism and anisotropy of mechanical properties of Si3N4p/Al-Mg-Si composites fabricated by sintering and extrusion

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

Single-crystal Elasticity of Phase Egg AlSiO3OH and Δ-Alooh by Brillouin Spectroscopy