Abstract:BackgroundControlled low strength materials (CLSM), known as flow able fill is used as a replacement of compacted soil in cases where the application of the latter is difficult or impossible. The low mechanical requirements compared with concrete enable the use of industrial wastes for the production of CLSM. In general, CLSM mixtures consist of standard materials such as Portland cement, fly ash, fine aggregate and water. However, other industrial by-products and recycled materials are also accepted and encouraged as long as they are considered to be available, cost-effective for specific application and the necessary characteristics of the mixture such as flowability, strength, excavatability, and density are acceptable.MethodsThe aim of this study is to evaluate the feasibility of incorporating red mud as a partial replacement for Portland cement into a controlled low-strength material (CLSM) made by industrial by-products (e.g., ponded ash and fly ash). A control mixture was initially produced with ponded ash, Portland cement, Class F fly ash, and water. For other mix proportions, red mud was substituted for Portland cement in amounts of 5, 10, 15, 20, 25, and 30 % by weight. The bleeding, flowability, fresh density, initial setting time of fresh CLSM mixtures were measured and the follows were hardened ones including compressive strength, corrosivity.ResultsExpectedly, all general properties of CLSM incorporating red mud did fall within the acceptable ranges. They performed well and conformed to the requirements of CLSM in ACI 229 standards with regard to flowability, bleeding rate, initial setting time, corrosivity and unconfined compressive strength.ConclusionsThe partial replacement of cement by red mud, possibly up to 30 % in mixtures, would reduce flowability and slightly increase corrosivity evidenced by pH but still meet the requirements. Especially, it was found that an increase in red mud content could lead to an improvement in the stability (bleeding rate) and accelerate the setting process on the performances of the proposed CLSM. Finally, with regard to strength at 28 days, CLSM with highest strength could be produced by an optimum replacement of 15 % red mud to cement. In overall, it is worth noting that red mud could be feasible and potential in use as a partial replacement to Portland cement in CLSM production.

Cement-based and alkali-activated controlled low-strength materials made from cup lump rubber for use as road materials

Preparation of controlled low-strength materials from alkali-excited red mud-slag-iron tailings sand and a study of the reaction mechanism

A state-of-the-art review of rubber modified cement-based materials: Cement stabilized base

Cement – natural rubber latex stabilised recycled concrete aggregate as a pavement base material

Mechanical Properties and Numerical Analyses of Basalt Fiber Crumb Rubber Mortars in Soft Rock Roadways

Laboratory Evaluation of the Use of Cement-Treated Construction and Demolition Materials in Pavement Base and Subbase Applications

Experimental study on strength and abrasion-resistance enhancement admixture

Using copper slag and fly ash stabilised with lime or cement as a road base material

Asphalt concrete improved by concentrated rubber latex and prevulcanized rubber latex – Performance and cost analysis

DEVELOPMENT OF VARIOUS TYPES OF CEMENTS FOR THE DEVICE OF STRUCTURAL LAYERS OF ROAD PAVEMENT BASED ON ASPHALT GRANULAR CONCRETE MIXTURES

Large-scale direct shear testing of waste crushed rock reinforced with waste rubber as pavement base/subbase materials

Feasibility study of a soil-based rubberized CLSM

Evaluation of Fresh Properties of Controlled Low-Strength Material Produced from Water Treatment Sludge-Fly Ash-Slag Mixture Using Alkaline Activation

Natural Rubber Latex-Modified Concrete with PET and Crumb Rubber Aggregate Replacements for Sustainable Rigid Pavements

Engineering properties of controlled low strength material (CLSM) incorporating red mud

Improved mechanistic performance of natural rubber latex modified pavement concretes in sulfate environments

FINITE ELEMENT ANALYSIS OF CONTROLLED LOW STRENGTH MATERIAL PAVEMENT BASES: FREE VIBRATION ANALYSIS

Sustainable controlled low strength material from waste materials for infrastructure applications: State-of-the-art

Use of waste rubber particles in cement-stabilized aggregate for the eco-friendly pavement base layer construction: Laboratory performance and field application

Microstructure Analysis and Mechanical Properties of Backfill Material Using Stone Sludge

Evaluation of cement treatment of reclaimed construction and demolition waste as road bases