Abstract:High power impulse magnetron sputtering (HiPIMS) is a popular physical vapor deposition (PVD) technology because of the high ionization of the sputtering materials, large coating density, good adhesion, and other favorable properties. However, this technique suffers some disadvantages such as the small deposition rate induced by the high target potential, the metallic droplets produced by the unstable discharge, and different ionizations for different sputtering materials, thereby hampering wider acceptance by the industry. A cylindric HiPIMS source in which the discharge is restricted in the cylinder is described in this paper. By using this source, coatings can be deposited with 100% ions without metallic droplets arising from the unstable discharge, and the unionized sputtered atoms cannot be extracted by the extraction grid with negative potential. Electron oscillation and repetitive sputtering of the unionized atoms occur in the cylinder to enhance collision and ionization. Due to the enlarged discharge area by the cylinder internal surface comparing with the area of the ion outlet (end face of the cylinder), the sputtering ions converge from the inwall to the center of the cylinder target and form an enhanced flow to spray out from the source, which will improve the deposition rate. The structure and discharge characteristics of the novel HiPIMS source are investigated by simulation and experiments. Our results indicate that 8 magnets can provide the reasonable magnetic field and the highest target utilization rate. The distributions of electrons and ions in the target each consist of 8 petals in the optimized magnetic structure, and the highest plasma density happens near the target, which is above 1.31017 m-3. The discharge characteristics confirm that the cylindric sputtering source can be operated under HiPIMS conditions and the evolution of the target currents with target voltage exhibits I-V characteristics typical of HiPIMS. An obvious pre-ionization is observed on the discharge glow and discharge current curves when the extra direct current (DC) is added. The racetrack area is about 60.0% of the target surface. The ion current curves are similar to those of the target currents, but a 40 s delay and about one-tenth current value are observed compared with the target currents. The sputtering is improved by the extra DC, inducing the increased metallic ions and the opposite evolution of gas ions. The results suggest that the cylindric sputtering source can be effectively used to conduct HiPIMS and is a novel way to improve and promote the application of HiPIMS.

Achieving a High Thermally Conductive One Micron AlN Deposition by High Power Impulse Magnetron Sputtering plus Kick

Improving the crystallinity and texture of oblique-angle-deposited AlN thin films using reactive synchronized HiPIMS

Study of TiAlN coatings deposited by continuous high power magnetron sputtering (C-HPMS)

Comparative Study of TiAlN Coatings Deposited by Different High-Ionization Physical Vapor Deposition Techniques

Novel Plasma Immersion Ion Implantation and Deposition Hardware and Technique Based on High Power Pulsed Magnetron Discharge

Low Temperature Deposition of Functional Thin Films on Insulating Substrates: Selective Ion Acceleration using Synchronized Floating Potential HiPIMS

Electromagnetic Control and Optimization of High Power Impulse Magnetron Sputtering Discharges in Cylindrical Source

Enhanced Electrical Properties of Copper Nitride Films Deposited via High Power Impulse Magnetron Sputtering

Magnetic Field Optimization and High-Power Discharge Characteristics of Cylindrical Sputtering Cathode

Steady state discharge optimization in high-power impulse magnetron sputtering through the control of the magnetic field

Optimization of Superconducting Niobium Nitride Thin Films via High-Power Impulse Magnetron Sputtering

Study of magnetic iron nitride thin films deposited by high power impulse magnetron sputtering

High power pulsed magnetron sputtering: A review on scientific and engineering state of the art

Microstructures and Mechanical Properties of CrN Coatings Deposited by HIPIMS

Plasma enhanced atomic layer deposition of silicon nitride using magnetized very high frequency plasma

Enhancement of Discharge and Deposition Rate in Dual-Pulse Pulsed Magnetron Sputtering: Effect of Ignition Pulse Width

Cylindric High Power Impulse Magnetron Sputtering Source and Its Discharge Characteristics

Tutorial: Reactive high power impulse magnetron sputtering (R-HiPIMS)

On the Control of Hot Nickel Target Magnetron Sputtering by Distribution of Power Pulses

High-rate deposition of ultra-thick silver film by hollow cathode magnetron sputtering

High Temperature Wear Behavior of Titanium Nitride Coating Deposited Using High Power Impulse Magnetron Sputtering