Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Clean Preparation of Formed Coke from Semi-coke by the Carbonated Consolidation Process

Effect of binder composition on the preparation of formed coke with low-rank coal

Highly Reactive Coke Made from Low-rank Coal: Relationship Between Thermal Properties and Multilevel Structure

Preparation of formed coke product as a coke substitute using a solid waste fuel: Trimethylbenzene improvement on coal tar pitch

Characterization of gasification-coke prepared with coal by-product and a high ratio of low-rank coal addition

Experimental investigation on physical and chemical properties of solid products from co-pyrolysis of bituminous coal and semi-coke

Activated Coke Prepared by Circulating Fluidized Bed Coal Pyrolysis Semi-coke for Desulphurization

Evolution of Coke Microstructure and Metallurgical Properties During Graphitization in a Blast Furnace

Experimental study on combustion and NO formation characteristics of semi-coke

Enhancement of coal tar pitch carbonization with biochar: A metallurgical formed biocoke product produced by waste coke breeze and bamboo powder

Study on improving the performance of blended Semi-coke coal water slurry based on multi-peak gradation technology

Characterization of semi-coke generated by coal-based direct reduction process of siderite

Bonding Mechanism of Binder and Low-Rank Coal During Carbonization

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Desulfurization Performances of Activated Coke Prepared from Fine Blue-Coke

Investigation on co-combustion of semi-coke and bituminous coal in oxygen-enriched atmosphere: Combustion, thermal conversion, and kinetic analyses

High Strength Clean Briquettes Production from Long‐flame Coal Fines by Using Polyvinyl Alcohol and Coal Slime As Binders

A comprehensive investigation on the structural transformation and dissolution loss reaction of coke during gasification in CO 2 atmosphere

Parameter Optimization of Waste Coal Briquetting and Particulate Matter Emissions Test During Combustion: A Case Study.

Influence of Na2CO3 on combustion performance of civil clean coke

Preheating Analysis of Semi-Coke in a Circulating Fluidized Bed and Its Kinetic Characteristics