Abstract:The development of readily accessible polymer acceptors is imperative to preserve the guiding principles of all-polymer solar cells as a low-cost and sustainable technology for alternative energy production. In this study, we report a computationally guided design and facile synthesis of new acceptor polymers comprising the alternating copolymer, PNIT, and the corresponding random copolymer, r-PNIT, which incorporate structurally simple naphthalene diimide (NDI) and isoindigo (IID) units. PNIT was prepared via direct arylation polymerization (DArP), which proceeds via C–H activation and avoids the use of toxic reagents and extended synthetic pathways for the monomer synthesis. PNIT has broad optical absorption in the 300–850 nm range and an enhanced absorption coefficient (47 × 103 cm–1) compared to r-PNIT (300–850 nm; 40 × 103 cm–1). When incorporated in all-polymer solar cells (APSCs) using PBDB-T as the donor polymer, PBDB-T:PNIT provides greater than two times the average (maximum) power conversion efficiency (PCE) of 5.18 ± 0.08 (5.32)% compared to that of PBDB-T:r-PNIT, 2.38 ± 0.16 (2.57)%, due to increased Jsc (10.36 vs 5.45 mA cm–2) and fill factor (FF) (0.58 vs 0.50) metrics. The PBDB-T:PNIT PCE is among the highest reported for an IID-based APSC and demonstrates the viability of DArP for the synthesis of new APSC acceptor polymers. Detailed morphological and microstructural investigations using atomic force microscopy (AFM) and grazing-incidence wide-angle X-ray scattering (GIWAXS), respectively, reveal enhanced texturing for PNIT, which enhances charge transport properties as supported by space-charge-limited current (SCLC) mobility measurements.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.chemmater.2c00065.Experimental procedures; synthesis and characterization of monomers and polymers; monomer and polymer NMR; GPC traces; TGA and DSC thermograms; contact angle measurements; CV and thin-film absorption measurements; DFT and TD-DFT calculations; device fabrication and testing parameters for APSCs and SCLC charge mobility measurements; and thin-film fabrication and measurement procedures for GIWAXS and AFM (PDF)This article has not yet been cited by other publications.

Naphthalene diimide-based random terpolymer acceptors for constructing all-polymer solar cells with enhanced fill factors

Terpolymer acceptors based on bithiophene imide for all-polymer solar cells

Naphthalene diimide-based random terpolymers with axisymmetric and asymmetric electron acceptors for controllable morphology and enhanced fill factors in all-polymer solar cells

Polymer acceptor based on naphthalene diimide and diethynylbenzo[1,2-b:4,5-b'] dithiophene units for efficient all-polymer solar cells

Acceptor–acceptor conjugated copolymers based on perylenediimide and benzothiadiazole for all‐polymer solar cells

An Efficient Polymer Acceptor Via a Random Polymerization Strategy Enables All-Polymer Solar Cells with Efficiency Exceeding 17%

Bandgap Engineering of Dual Acceptor-Containing Naphthalene Diimide Polymers for All-Polymer Solar Cells

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

Optimizing polymer aggregation and blend morphology for boosting the photovoltaic performance of polymer solar cells via a random terpolymerization strategy

Efficient Wide Bandgap All-Polymer Solar Cells Benefiting From A Random N-Type Copolymers Strategy

A polymer acceptor containing the B←N unitfor all-polymer solar cells with 14% efficiency

Thiophene-Fused Perylenediimide-Based Polymer Acceptors for High-Performance All-Polymer Solar Cells

All-Polymer Solar Cells Incorporating Readily Accessible Naphthalene Diimide and Isoindigo Acceptor Polymers for Improved Light Harvesting

High-efficiency all-polymer solar cells based on a pair of crystalline low-bandgap polymers.

Highly Efficient All‐Polymer Solar Cells Enabled by Random Ternary Copolymer Acceptors with High Tolerance on Molar Ratios

High-Efficiency All-Polymer Solar Cells with Poly-Small-Molecule Acceptors Having π-Extended Units with Broad Near-IR Absorption

Cyclopentadithiophene Cored A-π-D-π-A Non-Fullerene Electron Acceptor in Ternary Polymer Solar Cells to Extend the Light Absorption Up to 900 Nm

Regioregular Narrow‐Bandgap n‐Type Polymers with High Electron Mobility Enabling Highly Efficient All‐Polymer Solar Cells

Improving the fill factor of N2200-based all polymer solar cells by introducing EPPDI as a solid additive

A new random D-A copolymer based on two different benzotriazole units as co-acceptors for polymer solar cells

Thiophene with Oligoethylene Oxide Side Chain Enables Random Terpolymer Acceptor to Achieve Efficient All‐Polymer Solar Cells