Abstract:The ternary polymerization strategy of incorporating different donor and acceptor units forming terpolymers as photovoltaic materials has been proven advantageous in improving power conversion efficiencies (PCEs) of polymer solar cells (PSCs). Herein, a series of low band gap nonconjugated terpolymer acceptors based on two different fused-ring electron-deficient building blocks (IDIC16 and ITIC) with adjustable photoelectric properties were developed. As the third component, ITIC building blocks with a larger π-conjugation structure, shorter solubilizing side chains, and red-shifted absorption spectrum were incorporated into an IDIC16-based nonconjugated copolymer acceptor PF1-TS4, which built up the terpolymers with two conjugated building blocks linked by flexible thioalkyl chain-thiophene segments. With the increasing ITIC content, terpolymers show gradually broadened absorption spectra and slightly down-shifted lowest unoccupied molecular orbital levels. The active layer based on terpolymer PF1-TS4-60 with a 60% ITIC unit presents more balanced hole and electron mobilities, higher photoluminescence quenching efficiency, and improved morphology compared to those based on PF1-TS4. In all-polymer solar cells (all-PSCs), PF1-TS4-60, matched with a wide band gap polymer donor PM6, achieved a similar open-circuit voltage (Voc) of 0.99 V, a dramatically increased short-circuit current density (Jsc) of 15.30 mA cm–2, and fill factor (FF) of 61.4% compared to PF1-TS4 (Voc = 0.99 V, Jsc = 11.21 mA cm–2, and FF = 55.6%). As a result, the PF1-TS4-60-based all-PSCs achieved a PCE of 9.31%, which is ∼50% higher than the PF1-TS4-based ones (6.17%). The results demonstrate a promising approach to develop high-performance nonconjugated terpolymer acceptors for efficient all-PSCs by means of ternary polymerization using two different A–D–A-structured fused-ring electron-deficient building blocks.This article has not yet been cited by other publications.

Terpolymer acceptors based on bithiophene imide for all-polymer solar cells

Acceptor–acceptor conjugated copolymers based on perylenediimide and benzothiadiazole for all‐polymer solar cells

Benzodithiophene-modified terpolymer acceptors with reduced molecular planarity and crystallinity: improved performance and stability for all-polymer solar cells

High‐Performance All‐Polymer Solar Cells: Synthesis of Polymer Acceptor by a Random Ternary Copolymerization Strategy

Naphthalenediimide-based N-Type Polymer Acceptors with Pendant Twisted Perylenediimide Units for All-Polymer Solar Cells

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

Pt Complex-Based Terpolymer Acceptors Linked Through Ancillary Ligand For All-Polymer Solar Cells

Donor-Acceptor Photovoltaic Polymers Based On 1,4-Dithienyl-2,5-Dialkoxybenzene With Intramolecular Noncovalent Interactions

Dithiazolyl-benzothiadiazole-containing polymer acceptors: Synthesis, characterization, and all-polymer solar cells

Highly Efficient All‐Polymer Solar Cells Enabled by Random Ternary Copolymer Acceptors with High Tolerance on Molar Ratios

Polymer acceptor based on naphthalene diimide and diethynylbenzo[1,2-b:4,5-b'] dithiophene units for efficient all-polymer solar cells

Side-chain Optimization of Perylene Diimide-Thiophene Random Terpolymer Acceptors for Enhancing the Photovoltaic Efficiency of All-Polymer Solar Cells

All-Polymer Solar Cells with Perylenediimide Polymer Acceptors

Thiophene-Fused Perylenediimide-Based Polymer Acceptors for High-Performance All-Polymer Solar Cells

A Non-Conjugated Polymer Acceptor for Efficient and Thermally Stable All-Polymer Solar Cells

Regulation Of The Miscibility Of The Active Layer By Random Terpolymer Acceptors To Realize High-Performance All-Polymer Solar Cells

High-Performance Binary All-Polymer Solar Cells Enabled by a Y-derivative Pendant Random-Copolymerized Polymer Acceptor with a Broad Donor-Acceptor Matching Tolerance

Indacenodithienothiophene–naphthalene diimide copolymer as an acceptor for all-polymer solar cells

Novel High-Efficiency Polymer Acceptors Via Random Ternary Copolymerization Engineering Enables All-Polymer Solar Cells with Excellent Performance and Stability.

Thiophene with Oligoethylene Oxide Side Chain Enables Random Terpolymer Acceptor to Achieve Efficient All‐Polymer Solar Cells

Naphthalenediimide-alt-Fused Thiophene D-A Copolymers for the Application as Acceptor in All-Polymer Solar Cells.