Abstract:The ternary polymerization strategy of incorporating different donor and acceptor units forming terpolymers as photovoltaic materials has been proven advantageous in improving power conversion efficiencies (PCEs) of polymer solar cells (PSCs). Herein, a series of low band gap nonconjugated terpolymer acceptors based on two different fused-ring electron-deficient building blocks (IDIC16 and ITIC) with adjustable photoelectric properties were developed. As the third component, ITIC building blocks with a larger π-conjugation structure, shorter solubilizing side chains, and red-shifted absorption spectrum were incorporated into an IDIC16-based nonconjugated copolymer acceptor PF1-TS4, which built up the terpolymers with two conjugated building blocks linked by flexible thioalkyl chain-thiophene segments. With the increasing ITIC content, terpolymers show gradually broadened absorption spectra and slightly down-shifted lowest unoccupied molecular orbital levels. The active layer based on terpolymer PF1-TS4-60 with a 60% ITIC unit presents more balanced hole and electron mobilities, higher photoluminescence quenching efficiency, and improved morphology compared to those based on PF1-TS4. In all-polymer solar cells (all-PSCs), PF1-TS4-60, matched with a wide band gap polymer donor PM6, achieved a similar open-circuit voltage (Voc) of 0.99 V, a dramatically increased short-circuit current density (Jsc) of 15.30 mA cm–2, and fill factor (FF) of 61.4% compared to PF1-TS4 (Voc = 0.99 V, Jsc = 11.21 mA cm–2, and FF = 55.6%). As a result, the PF1-TS4-60-based all-PSCs achieved a PCE of 9.31%, which is ∼50% higher than the PF1-TS4-based ones (6.17%). The results demonstrate a promising approach to develop high-performance nonconjugated terpolymer acceptors for efficient all-PSCs by means of ternary polymerization using two different A–D–A-structured fused-ring electron-deficient building blocks.This article has not yet been cited by other publications.

Heteroheptacene-based acceptors with thieno[3,2- b ]pyrrole yield high-performance polymer solar cells

Introducing Electron-Withdrawing Linking Units and Thiophene π-Bridges into Polymerized Small Molecule Acceptors for High-Efficiency All-Polymer Solar Cells

Isomerization of Asymmetric Ladder‐Type Heteroheptacene‐Based Small‐Molecule Acceptors Improving Molecular Packing: Efficient Nonfullerene Organic Solar Cells with Excellent Fill Factors

Polymerized Small Molecular Acceptor with Branched Side Chains for All Polymer Solar Cells with Efficiency over 16.7%

Mapping Nonfullerene Acceptors with a Novel Wide Bandgap Polymer for High Performance Polymer Solar Cells

Thiophene-Fused Perylenediimide-Based Polymer Acceptors for High-Performance All-Polymer Solar Cells

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

Polymerized small-molecule acceptors based on vinylene as π-bridge for efficient all-polymer solar cells

Rational Design of Near‐Infrared Polymer Acceptors Using Steric Hindrance Strategy for High‐Performance Organic Solar Cells

Highly Efficient and Stable All-Polymer Solar Cells Enabled by Near-Infrared Isomerized Polymer Acceptors

Polymerizing Ladder-type Heteroheptacene-Cored Small-Molecule Acceptors for Efficient All-Polymer Solar Cells

Precisely Controlling the Position of Bromine on the End Group Enables Well‐Regular Polymer Acceptors for All‐Polymer Solar Cells with Efficiencies over 15%

High-Performance Polymer Acceptor Synthesized by an Asymmetric Copolymerization Strategy

Synthesis And Photovoltaic Properties From Inverted Geometry Cells And Roll-To-Roll Coated Large Area Cells From Dithienopyrrole-Based Donor-Acceptor Polymers

Terpolymer acceptors based on bithiophene imide for all-polymer solar cells

High-Efficiency All-Polymer Solar Cells with Poly-Small-Molecule Acceptors Having π-Extended Units with Broad Near-IR Absorption

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

Polymerizing M‐Series Acceptors for Efficient Polymer Solar Cells: Effect of the Molecular Shape

A Double-Cable Y-series-based Polymer Acceptor for Efficient All-Polymer Solar Cells: A New Strategy of Polymerizing Small Molecule Acceptor

All-Polymer Solar Cells with Perylenediimide Polymer Acceptors

Molecular Optimization on Polymer Acceptor Enables Efficient All‐Polymer Solar Cell with High Open‐Circuit Voltage of 1.10 V