Abstract:Non-fullerene electron acceptors have attracted enormous attention of the research community owing to their advantages of optoelectronic and chemical tunabilities for promoting high-performance polymer solar cells (PSCs). Among them, fused-ring electron acceptors (FREAs) are the most popular ones with the good structural planarity and rigidity, which successfully boost the power conversion efficiencies (PCEs) of PSCs to over 14%. In considering the cost-control of future scale-up applications, it is also worthwhile to explore novel structures that are easy to synthesize and still maintain the advantages of FREAs. In this work, we design and synthesize a new electron acceptor with an unfused backbone, 5,5'-((2,5-bis((2-hexyldecyl)oxy)-1,4-phenylene)bis(thiophene-2-yl))bis(methanylylidene)) bis(3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimal-ononitrile (ICTP), which contains two thiophenes and one alkoxy benzene as the core and 2-(3-oxo-2,3-dihydroinden-1-ylidene) malononitrile (IC) as the terminal groups. The synthetic route to ICTP involves only three steps, with high yields. Density functional theory calculations indicate that the non-covalent interactions, O center dot center dot center dot H and O center dot center dot center dot S, help reinforce the space conformation between the central core and the terminals. ICTP shows broad and strong absorption in the long-wavelength range between 500 and 760 nm. The highest occupied molecular orbital and lowest unoccupied molecular orbital levels of ICTP were measured to be -5.56 and -3.84 eV by cyclic voltammetry. The suitable absorption and energy levels make ICTP a good acceptor candidate for medium bandgap polymer donors. The best devices based on PBDB-T:ICTP showed a PCE of 4.43%, with an open circuit voltage (V-OC) of 0.97 V, a short circuit current density (J(SC)) of 8.29 mA.cm(-2), and a fill factor (FF) of 0.55, after adding 1% 1,8-diiodooctane (DIO) as the solvent additive. Atomic force microscopy revealed that DIO could ameliorate the strong aggregation in the blended film and lead to a smoother film surface. The hole and electron mobilities of the optimized device were measured to be 9.64 and 2.03 x 10(-5) cm(2).v(-1).s(-1), respectively, by the space-charge-limited current method. The relatively low mobilities might be responsible for the moderate PCE. Further studies can be performed to enlarge the conjugation length by including more aromatic rings. This study provides a simple strategy to design non-fullerene acceptors and a valuable reference for the future development of PSCs.

Cyclopentadithiophene Cored A-π-D-π-A Non-Fullerene Electron Acceptor in Ternary Polymer Solar Cells to Extend the Light Absorption Up to 900 Nm

Mapping Nonfullerene Acceptors with a Novel Wide Bandgap Polymer for High Performance Polymer Solar Cells

Non-fullerene Acceptors with a Thieno[3,4-c]pyrrole-4,6-dione (TPD) Core for Efficient Organic Solar Cells

Dithienopicenocarbazole-Based Acceptors For Efficient Organic Solar Cells With Optoelectronic Response Over 1000 Nm And An Extremely Low Energy Loss

[6,6]-Phenyl-c61-butyric Acid 2-((2-(dimethylamino)ethyl)(methyl)amino)-ethyl Ester As an Acceptor and Cathode Interfacial Material in Polymer Solar Cells

Near‐Infrared Electron Acceptors with Fluorinated Regioisomeric Backbone for Highly Efficient Polymer Solar Cells

Cyclopentadithiophene-cored Non-Fullerene Acceptors for Efficient Polymer Solar Cells with Superior Stability

Enhancement Of Intra- And Inter-Molecular Pi-Conjugated Effects For A Non-Fullerene Acceptor To Achieve High-Efficiency Organic Solar Cells With An Extended Photoresponse Range And Optimized Morphology

Nonfullerene Acceptor with Strong Near-Infrared Absorption for Polymer Solar Cells

Angular-Shaped Dithienonaphthalene-Based Nonfullerene Acceptor for High-Performance Polymer Solar Cells with Large Open-Circuit Voltages and Minimal Energy Losses

A Narrow Band Gap Non-Fullerene Electron Acceptor Based on a Dithieno-3,2-b:2′,3′-Dlpyrrole Unit for High Performance Organic Solar Cells with Minimal Highest Occupied Molecular Orbital Offset

Wide Bandgap Polymer Donors with an Acceptor1-Π-acceptor2-π Configuration for Efficient Polymer Solar Cells

Rationally pairing photoactive materials for high-performance polymer solar cells with efficiency of 16.53%

Low-bandgap nonfullerene acceptor based on thieno[3,2-b]indole core for highly efficient binary and ternary organic solar cells

Highly Efficient Organic Solar Cells Based on S,N-Heteroacene Non-Fullerene Acceptors

Unaxisymmetric Non-Fused Electron Acceptors for Efficient Polymer Solar Cells

Simple Modulation of Side-chains of Near-infrared Absorbing Non-fullerene Acceptor for Higher Short-circuit Current Density

Hybrid Nonfused-Ring Electron Acceptors with Fullerene Pendant for High-Efficiency Organic Solar Cells

Highly Efficient Ternary Solar Cells with Efficient Förster Resonance Energy Transfer for Simultaneously Enhanced Photovoltaic Parameters

A Near-Infrared Polymer Acceptor Enables over 15% Efficiency for All-Polymer Solar Cells

A Simple Electron Acceptor with Unfused Backbone for Polymer Solar Cells