Abstract:The ternary polymerization strategy of incorporating different donor and acceptor units forming terpolymers as photovoltaic materials has been proven advantageous in improving power conversion efficiencies (PCEs) of polymer solar cells (PSCs). Herein, a series of low band gap nonconjugated terpolymer acceptors based on two different fused-ring electron-deficient building blocks (IDIC16 and ITIC) with adjustable photoelectric properties were developed. As the third component, ITIC building blocks with a larger π-conjugation structure, shorter solubilizing side chains, and red-shifted absorption spectrum were incorporated into an IDIC16-based nonconjugated copolymer acceptor PF1-TS4, which built up the terpolymers with two conjugated building blocks linked by flexible thioalkyl chain-thiophene segments. With the increasing ITIC content, terpolymers show gradually broadened absorption spectra and slightly down-shifted lowest unoccupied molecular orbital levels. The active layer based on terpolymer PF1-TS4-60 with a 60% ITIC unit presents more balanced hole and electron mobilities, higher photoluminescence quenching efficiency, and improved morphology compared to those based on PF1-TS4. In all-polymer solar cells (all-PSCs), PF1-TS4-60, matched with a wide band gap polymer donor PM6, achieved a similar open-circuit voltage (Voc) of 0.99 V, a dramatically increased short-circuit current density (Jsc) of 15.30 mA cm–2, and fill factor (FF) of 61.4% compared to PF1-TS4 (Voc = 0.99 V, Jsc = 11.21 mA cm–2, and FF = 55.6%). As a result, the PF1-TS4-60-based all-PSCs achieved a PCE of 9.31%, which is ∼50% higher than the PF1-TS4-based ones (6.17%). The results demonstrate a promising approach to develop high-performance nonconjugated terpolymer acceptors for efficient all-PSCs by means of ternary polymerization using two different A–D–A-structured fused-ring electron-deficient building blocks.This article has not yet been cited by other publications.

Cyclopentadithiophene-cored Non-Fullerene Acceptors for Efficient Polymer Solar Cells with Superior Stability

Dithienopicenocarbazole-Based Acceptors For Efficient Organic Solar Cells With Optoelectronic Response Over 1000 Nm And An Extremely Low Energy Loss

Mapping Nonfullerene Acceptors with a Novel Wide Bandgap Polymer for High Performance Polymer Solar Cells

Cyclopentadithiophene Cored A-π-D-π-A Non-Fullerene Electron Acceptor in Ternary Polymer Solar Cells to Extend the Light Absorption Up to 900 Nm

Side-chain Modification of Non-fullerene Acceptors for Organic Solar Cells with Efficiency over 18%

An Unfused‐Core‐Based Nonfullerene Acceptor Enables High‐Efficiency Organic Solar Cells with Excellent Morphological Stability at High Temperatures

Angular-Shaped Dithienonaphthalene-Based Nonfullerene Acceptor for High-Performance Polymer Solar Cells with Large Open-Circuit Voltages and Minimal Energy Losses

High‐Efficiency Organic Solar Cells Based on a Low‐Cost Fully Non‐Fused Electron Acceptor

Non‐Fullerene Organic Solar Cells Based on Benzo[1,2‐b:4,5‐b′]difuran‐Conjugated Polymer with 14% Efficiency

Nonfused Electron Acceptors Based on the 2D-Extended Quinoxaline Core for Organic Solar Cells

Dithienonaphthalene-Based Non-fullerene Acceptors with Different Bandgaps for Organic Solar Cells

Highly efficient and stable binary and ternary organic solar cells using polymerized nonfused ring electron acceptors

Unfused-ring small molecule acceptors based on A1-D-A2-D-A1 architecture with low non-radiative energy loss and excellent air stability

Enhancing the Photovoltaic Performance of a Benzo[ c ][1,2,5]thiadiazole-Based Polymer Donor via a Non-Fullerene Acceptor Pairing Strategy

Y‐type Non‐fullerene Acceptors with Outer Branched Side Chains and Inner Cyclohexane Side Chains for 19.36% Efficiency Polymer Solar Cells

Fused‐Ring Core Engineering for Small Molecule Acceptors Enable High‐Performance Nonfullerene Polymer Solar Cells

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

Design of simple-structure wide-bandgap conjugated polymers based on BDT for efficient non-fullerene solar cells

Towards High-Efficiency Non-Fullerene Organic Solar Cells: Matching Small Molecule/polymer Donor/acceptor

Efficient and Stable Nonfused Ring Small Molecule Acceptors Powered by an Electron Donating Unit for Organic Solar Cells

Small-molecule acceptors with long alkyl chains for high-performance as-cast nonfullerene organic solar cells