Abstract:A combination of high open-circuit voltage (Voc) and short-circuit current density (Jsc) typically creates effective organic solar cells (OSCs). Y5, a member of the Y-series acceptors, can achieve high Voc of 0.94 V with PM6 but low Jsc of 12.8 mA cm–2. To maintain the high Voc while increasing the Jsc of devices, we developed a new nonfullerene acceptor, namely, BTP-C2C4-N, by extending the conjugation of a Y5 molecule with a naphthalene-based end acceptor. In comparison with Y5-based devices, PM6:BTP-C2C4-N-based devices exhibited significantly higher Jsc of 18.2 mA cm–2 followed by a high Voc. To further increase the photovoltaic properties of BTP-C2C4-N analogues, BTP-C4C6-N and BTP-C6C8-N molecules with better processability and film morphology are obtained by adjusting the alkyl branched chain length. The optimized OSCs based on BTP-C4C6-N with a moderate alkyl branched chain length exhibited the best PCE of 12.4% with a high Voc of 0.94 V and Jsc of 20.7 mA cm–2. Notably, the devices achieved a low energy loss of 0.49 eV (0.51 eV for Y5 system) accompanied by a small nonradiative energy loss. The results indicate that nonfullerene acceptors with extended terminal motifs and optimized branched chain lengths can effectively enhance the performance of OSCs and reduce energy loss.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c04273?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c04273</a>.Detailed information of material synthesis, device preparation, absorption curve, DFT calculations, GIWAXS patterns for neat PM6 and Y5, the AFM image of Y5 blend, data of mobility, contact angle measurements, and so forth (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c04273/suppl_file/am1c04273_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Y‐type Non‐fullerene Acceptors with Outer Branched Side Chains and Inner Cyclohexane Side Chains for 19.36% Efficiency Polymer Solar Cells

Mapping Nonfullerene Acceptors with a Novel Wide Bandgap Polymer for High Performance Polymer Solar Cells

Side-chain Modification of Non-fullerene Acceptors for Organic Solar Cells with Efficiency over 18%

π-Extended Nonfullerene Acceptors for Efficient Organic Solar Cells with a High Open-Circuit Voltage of 0.94 V and a Low Energy Loss of 0.49 eV

19.32% Efficiency Polymer Solar Cells Enabled by Fine‐Tuning Stacking Modes of Y‐Type Molecule Acceptors: Synergistic Bromine and Fluorine Substitution of the End Groups

Shorter alkyl chain in thieno[3,4-c]pyrrole-4,6-dione (TPD)-based large bandgap polymer donors – Yield efficient non-fullerene polymer solar cells

18.6% Efficiency All‐Polymer Solar Cells Enabled by a Wide Bandgap Polymer Donor Based on Benzo[1,2‐d:4,5‐d′]bisthiazole

Cyclopentadithiophene-cored Non-Fullerene Acceptors for Efficient Polymer Solar Cells with Superior Stability

Achieving Efficient Ternary Organic Solar Cells Using Structurally Similar Non‐Fullerene Acceptors with Varying Flanking Side Chains

Polymerized Small Molecular Acceptor with Branched Side Chains for All Polymer Solar Cells with Efficiency over 16.7%

Developing Halogen‐Free Polymer Donors for Efficient Nonfullerene Organic Solar Cells by Addition of Highly Electron‐Deficient Diketopyrrolopyrrole Unit

Non‐Fullerene Organic Solar Cells Based on Benzo[1,2‐b:4,5‐b′]difuran‐Conjugated Polymer with 14% Efficiency

A Double-Cable Y-series-based Polymer Acceptor for Efficient All-Polymer Solar Cells: A New Strategy of Polymerizing Small Molecule Acceptor

Enhancing the Photovoltaic Performance of a Benzo[ c ][1,2,5]thiadiazole-Based Polymer Donor via a Non-Fullerene Acceptor Pairing Strategy

Wide bandgap donor polymers containing carbonyl groups for efficient non-fullerene polymer solar cells

Guest-oriented non-fullerene acceptors for ternary organic solar cells with over 16.0% and 22.7% efficiencies under one-sun and indoor light

Alkyl Chain Tuning of Non-fullerene Electron Acceptors toward 18.2% Efficiency Binary Organic Solar Cells

Introducing Electron-Withdrawing Linking Units and Thiophene π-Bridges into Polymerized Small Molecule Acceptors for High-Efficiency All-Polymer Solar Cells

Challenging PM6-alike donor polymers for paring a Y-type state-of-art acceptor in binary blends for bulk heterojunction solar cells

Non-fullerene acceptors with branched side chains and improved molecular packing to exceed 18% efficiency in organic solar cells

Single-Junction Organic Solar Cell with over 15% Efficiency Using Fused-Ring Acceptor with Electron-Deficient Core