Abstract:Non-fullerene electron acceptors have attracted enormous attention of the research community owing to their advantages of optoelectronic and chemical tunabilities for promoting high-performance polymer solar cells (PSCs). Among them, fused-ring electron acceptors (FREAs) are the most popular ones with the good structural planarity and rigidity, which successfully boost the power conversion efficiencies (PCEs) of PSCs to over 14%. In considering the cost-control of future scale-up applications, it is also worthwhile to explore novel structures that are easy to synthesize and still maintain the advantages of FREAs. In this work, we design and synthesize a new electron acceptor with an unfused backbone, 5,5'-((2,5-bis((2-hexyldecyl)oxy)-1,4-phenylene)bis(thiophene-2-yl))bis(methanylylidene)) bis(3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimal-ononitrile (ICTP), which contains two thiophenes and one alkoxy benzene as the core and 2-(3-oxo-2,3-dihydroinden-1-ylidene) malononitrile (IC) as the terminal groups. The synthetic route to ICTP involves only three steps, with high yields. Density functional theory calculations indicate that the non-covalent interactions, O center dot center dot center dot H and O center dot center dot center dot S, help reinforce the space conformation between the central core and the terminals. ICTP shows broad and strong absorption in the long-wavelength range between 500 and 760 nm. The highest occupied molecular orbital and lowest unoccupied molecular orbital levels of ICTP were measured to be -5.56 and -3.84 eV by cyclic voltammetry. The suitable absorption and energy levels make ICTP a good acceptor candidate for medium bandgap polymer donors. The best devices based on PBDB-T:ICTP showed a PCE of 4.43%, with an open circuit voltage (V-OC) of 0.97 V, a short circuit current density (J(SC)) of 8.29 mA.cm(-2), and a fill factor (FF) of 0.55, after adding 1% 1,8-diiodooctane (DIO) as the solvent additive. Atomic force microscopy revealed that DIO could ameliorate the strong aggregation in the blended film and lead to a smoother film surface. The hole and electron mobilities of the optimized device were measured to be 9.64 and 2.03 x 10(-5) cm(2).v(-1).s(-1), respectively, by the space-charge-limited current method. The relatively low mobilities might be responsible for the moderate PCE. Further studies can be performed to enlarge the conjugation length by including more aromatic rings. This study provides a simple strategy to design non-fullerene acceptors and a valuable reference for the future development of PSCs.

Unaxisymmetric Non-Fused Electron Acceptors for Efficient Polymer Solar Cells

Hybrid Nonfused Electron Acceptors with Perylene Diimide Pendants for Organic Solar Cells

Mapping Nonfullerene Acceptors with a Novel Wide Bandgap Polymer for High Performance Polymer Solar Cells

2D/1A Ternary Blend System Enables Non-Fused Ring Electron Acceptor Based Polymer Solar Cells with Improved Photovoltaic Parameters

Near‐Infrared Electron Acceptors with Fluorinated Regioisomeric Backbone for Highly Efficient Polymer Solar Cells

Non-Fullerene Acceptor for Organic Solar Cells with Chlorination on Dithieno[3,2-b:2′,3′-d]pyrrol Fused-Ring

A Fully Non‐fused Ring Acceptor with Planar Backbone and Near‐IR Absorption for High Performance Polymer Solar Cells

Half-Planar-Half-Twisted Small Molecule Acceptors for Efficient Polymer Solar Cells

Cyclopentadithiophene Cored A-π-D-π-A Non-Fullerene Electron Acceptor in Ternary Polymer Solar Cells to Extend the Light Absorption Up to 900 Nm

Fused Nonacyclic Electron Acceptors with Additional Alkyl Side Chains for Efficient Polymer Solar Cells

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

Unfused-ring Acceptors with Dithienobenzotriazole Core for Efficient Organic Solar Cells

A Noncovalently Fused‐Ring Asymmetric Electron Acceptor Enables Efficient Organic Solar Cells

Completely non-fused electron acceptor with 3D-interpenetrated crystalline structure enables efficient and stable organic solar cell

Nonfused Nonfullerene Acceptors with an A-D-A'-D-A Framework and a Benzothiadiazole Core for High-Performance Organic Solar Cells.

Enhanced Crystal Network and Charge Transfer of Non-Fused Ring Electron Acceptor Via Interchain Interaction Enable Efficient and Stable Organic Solar Cells

A Simple Electron Acceptor with Unfused Backbone for Polymer Solar Cells

Optimizing the Molecular Structure of Dithienophthalimide-Based Nonfused Ring Electron Acceptors for Efficient Organic Solar Cells

Integrated linker-regulation and ring-fusion engineering for efficient additive-free non-fullerene organic solar cells

Optimizing Molecular Crystallinity and Suppressing Electron‐Phonon Coupling in Completely Non‐fused Ring Electron Acceptors for Organic Solar Cells

Enhancing the Intermolecular Interactions of Ladder-Type Heteroheptacene-Based Nonfullerene Acceptors for Efficient Polymer Solar Cells by Incorporating Asymmetric Side Chains