Abstract:Introduction: Traditional prosthetic solutions expose the amputee to numerous problems that limit his ability to safely perform the normal activities of daily life. In order to eliminate the problems related to the use of the traditional prosthesis with socket, a new technique was developed for fixing the prosthesis to the amputees based on the principle of osseointegration. The aim of this paper is to study and analyze the stress distribution on the interface between a trans-humeral osseointegrated prosthetic implant and the residual bone, identifying the most stressed areas and thus foreseeing possible failure phenomena of the entire prosthetic system and, after, to compare the stress distribution on three different prosthetic designs that differ from each other for some geometric characteristics. Materials and methods: A healthy individual mimics two fall scenarios of which the trans-humeral amputees can most likely be victims: Static fall and Dynamic fall. A force platform (P-6000, BTS Bioengineering) is required for load data acquisition. The CAD model of the trans-humeral osseointegrated implant was created following the guidelines of the OPRA implant. The bone model was created starting from the CAT scan of a left humerus. The FEM simulation was conducted throught a linear analysis. Results: Both during static fall and dynamic fall, similar trends have been observed for the reaction force Fz, the torque moment Tz, the bending moments Mx and My. From the analysis of the von Mises stress distribution it was found that the stress distribution is more homogeneous in the case where the thread of the fixture is made by a triangular profile with height of the thread equal to 0.5 mm. However, it can be seen that, when passing from a thread with height of 0.5 mm to a 1 mm, there is a slight decrease in the stress on the whole contact zone between the fixture and the humerus. The same improvement can also be seen in the case of trapezoidal threading. Conclusion: By modifying the height and/or by varying the thread profile, are obtained slightly better results with respect to the case with a 0.5 mm height triangular thread.

Comparative study of a femoral amputated limb with and without implant

Finite Element Modeling of the Contact Interface Between Trans-Tibial Residual Limb and Prosthetic Socket.

Methodology to Investigate Effect of Prosthetic Interface Design on Residual Limb Soft Tissue Deformation

Is skin pressure a relevant factor for socket assessment in patients with lower limb amputation?

Enhanced orthopedic implant design for transfemoral amputation incorporating a honeycomb structure technology

Comparison of mechanical conditions in a lower leg model with 5 or 6 tissue types while exposed to prosthetic sockets applying finite element analysis

3D Finite Element Dynamic Analysis of Interface Stress at Residual Limb of a Trans-Tibial Amputee

Influence of the Scale Reduction in Designing Sockets for Trans-Tibial Amputees.

Effects of Prosthetic Socket Design on Residual Femur Motion Using Dynamic Stereo X-Ray - A Preliminary Analysis

Assessing Socket Fit Effects on Pressure and Shear at a Transtibial Residuum/Socket Interface

[Inertial Effects on Interface Pressure Between Prosthetic Socket and Residual Limb].

Comparative biomechanical analysis of a conventional/novel hip prosthetic socket

A Quasi-Dynamic Nonlinear Finite Element Model to Investigate Prosthetic Interface Stresses During Walking for Trans-Tibial Amputees

Finite element modelling of a residual lower-limb in a prosthetic socket: a survey of the development in the first decade

A clinical comparison of a digital versus conventional design methodology for transtibial prosthetic interfaces

[Three-Dimensional Finite Element Analyses on the Transtibial Residual Limb and Its Prosthetic Socket].

Virtual simulation of an osseointegrated trans-humeral prosthesis: A falling scenario

Numerical simulation and experimental testing for static failure prediction in additively manufactured below-knee prosthetic sockets

3D Modeling and Biomechanical Analysis to Residual Limb and Prosthetic Socket

Modeling and analysis of a prosthetic foot: A numerical simulation case study

Load transfer mechanics between trans-tibial prosthetic socket and residual limb--dynamic effects.