Abstract:As tellurides and selenides of Bismuth are extensively used thermoelectric materials in the low-temperature range with refrigeration application, A concerted effort is put forth to boost the ZT by co-doping the pristine Bi 2 Se 3 with antimony (Sb) on cation end and tellurium (Te) on anion side of the compound. The double sintered solid-state reaction method is employed in the preparation of Bi 2 Se 3 and (Bi 1− x Sb x ) 2 Se 2.7 Te 0.3 polycrystalline pellets, with x = 0.02, 0.04, and 0.06. The sample exhibits a rhombohedral structure with the space group of R m. FESEM and EDAX analysis are used to confirm surface morphology and elemental composition of the produced samples. The thermoelectric measurements for the pristine and co-doped samples were conducted by the physical property measurement system as well as a considerable increase in the Seebeck coefficient of − 115 μV/K is observed for 0.02 doping of the Sb which is 4.2 times greater than as for pristine (S = − 28 μV/K). Higher concentration doping ( x = 0.04, 0.06) has not reflected any Seebeck coefficient advancement. In contrast, the lowest total thermal conductivity at a low-temperature regime (< 50 K) is observed for x = 0.06 doping concentration which at near room temperature increases beyond the pristine thermal conductivity; whereas, x = 0.02, 0.04 doping concentration shows a decrement in total thermal conductivity at low, at room temperature region the values are almost equivalent to that of pristine. The co-doped samples' electrical resistivity is substantially less than pristine sample. The highest power factor of 3 × 10 –4 μW/mK 2 is obtained for the x = 0.02 sample. The highest ZT value for the x = 0.02 sample is almost 28 times more than a pristine sample. We conducted a study where we combined experimental and DFT methods to investigate thermoelectric properties incorporated into pristine and doped with antimony and tellurium on Bi 2 Se 3 . We have employed this combination to investigate the partial density of states, Seebeck coefficient, power factor using the Boltzmann transport equation. Theoretical thermoelectric data were derived and compared to experimental observations. Hence, using combined experimental and theoretical investigations helps to predict with higher accuracy of thermoelectric properties of semiconducting materials.

Potential improvement in power factor of (Bi0.98Ge0.02)2Te2.7Se0.3 compound due to defect engineering

Defect Engineering of Bi2SeO2 Thermoelectrics

Isovalent co-alloying contributes to considerable improvement in thermoelectric performance of BiSe bulks with weak anisotropy

Vacancy-Based Defect Regulation for High Thermoelectric Performance in Ge9Sb2Te12-x Compounds

Defect Structure Regulation and Thermoelectric Transfer Performance in N-Type Bi2-xSbxTe3-ySey-based Compounds

Enhancing thermoelectric behavior of bismuth Selenide crystal via substitution of sulfur and tellurium

Ultralow lattice thermal conductivity and enhanced power generation efficiency realized in Bi2Te2.7Se0.3/Bi2S3 nanocomposites

Synergetic enhancement of power factor and suppression of lattice thermal conductivity via electronic structure modification and nanostructuring on Ni and B co-doped p-type Si-Ge alloy

Optimizing Thermoelectric Performance of Hybrid Crystals Bi2O2Se1-xTex in the Bi2O2X System

Enhanced Thermoelectric Performance in Ge 0.955− x Sb x Te/FeGe 2 Composites Enabled by Hierarchical Defects

Tailoring Thermoelectric Performance of n-type Bi2Te3 through Defect Engineering and Conduction Band Convergence

Unraveling electronic origins for boosting thermoelectric performance of p-type (Bi,Sb) 2 Te 3

Engineering atomic-level crystal lattice and electronic band structure for extraordinarily high average thermoelectric figure of merit in n-type PbSe

Synergistically Optimized Thermal Conductivity and Carrier Concentration in GeTe by Bi–Se Codoping

A comprehensive experimental and DFT analysis on thermoelectric properties of Sb, Te co-doped Bi2Se3 polycrystals

Thermoelectric power factor of Bi-Sb-Te and Bi-Te-Se alloys and doping strategy: First-principles study

High performance of Mg3Bi1.5Sb0.5 based materials for power generation: Revealing the counter-intuitive effect of tuning Bi content on the thermoelectric properties

Atomic Level Defect Structure Engineering for Unusually High Average Thermoelectric Figure of Merit in N‐type PbSe Rivalling PbTe

Modifying Roles of CuSbSe2 in Realizing High Thermoelectric Performance of GeTe

Synergistic optimization of the thermoelectric performance of BiSbSe3 using doping and multi-scale defect engineering

Enhanced power factor of Bi<sub>0.5</sub>Sb<sub>1.5</sub>Te<sub>3</sub> thin films via PbTe incorporating and annealing