Abstract:Parameter values adopted in railway engineering analysis at present are generally obtained through triaxial tests, whereas the remarkable difference between the actual stress path during train passage and the loading path in cyclic triaxial tests may lead to inaccurate predictions and even engineering problems. Published researches show that the actual stress path probably contains principal stress rotation(PSR), which has a sisgnificant influence on the mechanical response of soil. However, the conventional approach, i.e. cyclic triaxial test is not efficient in simulating this complicated stress path involving PSR. Instead, hollow cylinder test with cyclic shear stress has been proved to be an excellent selection for PSR study. In order to obtain reliable stress path for guiding hollow cylinder tests, three-dimensional calculation for a certain urban railway is carried out; and the distribution regularity of cyclic stress amplitudes, cycle numbers and PSR under train loads is analyzed. Furthermore, a series of cyclic torsional shear tests on hollow cylinder samples is employed to simulate the complex stress path and to research the deformation and pore pressure accumulation properties of saturated soft clay. Considering stress in foundation soil decreasing along with the depth increasing, various cyclic stress amplitudes corresponding to different depths are adopted in this experiment study. Three-dimensional calculation shows that the major principal stress axis will rotate from -90 degrees to 90 degrees during the train loading passage as well as the number and amplitude of stress waves reduce gradually with the increase of depth. It is also shown that both PSR and stress are quite sensitive to train loads as the upper soil element can identify a single wheel load while the lower soil element can just identify a bogie and even the whole train load. And through the cyclic torsional shear tests, it's obvious that the rotation of principal stress can promote the accumulation of pore pressure and strain in soft soil foundations significantly; and in the case when vertical cyclic stress amplitude equals to 15 kPa, the pore pressure and strain in cyclic torsional shear test are 77% and nearly 50% higher than that in cyclic triaxial test respectively. What's more, as the cyclic stress amplitude increases, the gap of cumulative pore pressure and strain between that two types of tests will enlarge further, which may even result in essential difference that samples in triaxial tests show only small strain whereas failure in torsional shear tests.

Strain Cyclic Characteristics and Ratchetting Behaviors of High-Speed Railway Train Axle Steel EA4T

Uniaxial and non-proportionally multiaxial ratcheting of U71Mn rail steel: experiments and simulations

A cyclic visco-plastic constitutive model for the ratcheting behavior of U75VG rail steel under a wide range of loading rates

Experimental characterization and numerical modeling on the external impacting of high-speed railway axle EA4T steel

Mechanical properties and microstructure of the heterogeneous DZ2 axle steel under high-strain-rate compression at ambient temperature

Corrosion fatigue behaviors and life prediction of railway axle EA4T steel with artificial indentation

Ratcheting assessment of low yield point steel BLY160: Experimental analysis and constitutive modelling

Strain amplitude-dependent cyclic softening behavior of carbide-free bainitic rail steel: Experiments and modeling

High cycle fatigue properties and fatigue crack propagation behavior of a bainite railway axle steel

Effect of ultrasonic rolled material layer on the corrosion fatigue resistance of railway axle EA4T alloy steel

Enhancement of Fatigue Endurance Limit through Ultrasonic Surface Rolling Processing in EA4T Axle Steel

Corrosion fatigue mechanism and life prediction of railway axle EA4T steel exposed to artificial rainwater

Ratcheting Assessment of Rail Steel at Elevated Temperatures in the Presence of Dynamic Strain Aging

The effect of microstructure evolution on the ratchetting-fatigue interaction of carbide-free bainite rail steels under different heat-treatment conditions

Research on mechanical response of soft clay under cyclic loading involving principal stress rotation

Experimental study on uniaxial and nonproportionally multiaxial ratcheting of SS304 stainless steel at room and high temperatures

Modeling of Low Cycle Behavior of P92 Steel Based on Cyclic Plasticity Constitutive Equations

Fatigue life enhancement of foreign object impacted railway axle EA4T steel with surface shot peening

Corrosion fatigue lifetime assessment of high-speed railway axle EA4T steel with artificial scratch

Experimental and numerical insights into fatigue crack propagation of railway component with gradient residual stress

Mechanical performance of low-yield-point steel LYP225 under cyclic loading