Abstract:The shift of the industrial focus from fuel to chemicals have urged the researchers to obtain a suitable petrochemical feedstock for the FCC unit. Currently, the slurry phase hydroprocessing is a boon for industrialists to upgrade the crude oil using dispersed catalysts. This hydroprocessed crude oil obtained from slurry phase reaction prevents the FCC catalyst unit from getting rapidly poisoned as most of the impurities is removed from the crude oil such as asphaltenes, resins, heavy metal, sulfur etc. This study puts forward the influence of reaction temperature and time on the hydroprocessing of the crude oil. First, the screening of three separate forms of unsupported trimetallic NiMoW catalysts i.e., as-synthesized (CAT1), sulfided (CAT2), and oil-soluble sulfided (CAT3) at 420 °C and 120 bar of hydrogen pressure has been performed. After screening out the best catalyst (CAT3) based on greater conversion results of heavier hydrocarbon fractions to lighter hydrocarbon fractions, further a detailed experimental study for the hydroprocessing of crude oil under hydrogen pressure (120 bar) with varying reaction temperatures (410, 420, 430 °C) and time period (3, 4 and 5 hours) has been carried. With the rise in temperature from 410 to 430 °C, although the higher conversion of heavier fractions is obtained but the increased amount in the coke weight % restricts the use of very high temperatures for slurry hydroprocessing of crude oil. At 420 °C and 120 bar H 2 pressure, CAT1 catalyst shows a reduction in heavy vacuum gas oil (>450 °C) from 20.05 wt% to 11.1 wt%, and rise in middle distillate from 37.02 wt% to 50.4 wt%. When CAT2 catalyst is employed, a decrease in heavy VGO from 20.05 wt% to 9.3 wt% was observed with an increase in the middle distillates from 37.02 wt% to 52.1 wt%. CAT3 catalyst leads to maximum reduction in heavy VGO from 20.05 wt% to 7.1 wt% with an increase in the middle distillates from 37.02 wt% to 55.2 wt%, which shows the importance of oil-soluble catalyst to obtain better quality petro FCC feed. The kinetic study has also been performed for a better understanding of the reaction pathway. Based on the kinetic study, the activation energy associated with each hydrocarbon fraction has been determined and presented in the work. Such detailed study covering all these valuable parameters along with kinetic study has not been presented till now which is the novelty of our work also.

Catalyst grading technology for promoting the diesel hydrocracking to naphtha

Fluid Mixing Optimization Strategy of Catalytic Reactor for Marine SCR System

Selective hydrocracking of light cycle oil into high-octane gasoline over bi-functional catalysts

Combined Process of Hydrocracking and Hydrofining of Coal Tar

IMPACT OF ADDITIONAL CATALYSTS ON NITROGEN DISTRIBUTION IN RESIDUE OIL SLURRY-BED HYDROCRACKING

Impact of Pt/Al-MCM-41 Catalyst Metal/Acid Ratio in Hydrocracking of Bio-Alkanes for Bio-Jet Fuel Production

Hydrocracking of Bio-Alkanes over Pt/Al-MCM-41 Mesoporous Molecular Sieves for Bio-Jet Fuel Production

Development of New Generation Catalysts for Selective Hydrodesulfurization of Fcc Naphtha

Selective hydrocracking of poly-aromatics to mono-aromatics in a catalyst grading system of NiMo/Al 2 O 3 -HY and NiMo/Beta

The gradient fabrication and optimization of metal-acid bifunctional catalysts for the hydrogenation of n-C16 to produce bio-jet fuel component

Effect of Catalyst on Distribution of Nitrogen in Products from Residue Hydrocracking

A review on upgrading and viscosity reduction of heavy oil and bitumen by underground catalytic cracking

Bifunctional catalyst with high efficiency for converting hydrocarbons: The enhanced diffusion between micro and meso-pores

Development and Commercial Application of High Efficiency Catalysts for Resid Hydrotreating

Effect of Metal Ratio and Preparation Method on Nickel–Tungsten Carbide Catalyst for Hydrocracking of Distillers Dried Grains with Solubles Corn Oil

Crude oil hierarchical catalytic cracking for maximizing chemicals production: Pilot-scale test, process optimization strategy, techno-economic-society-environment assessment

An inclusive experimental and kinetic understanding of the slurry phase hydroprocessing of crude oil with an active dispersed catalyst to obtain refined fuel

Commercial Application of 3996/3976 Catalyst in Jilin Petrochemical Company

Application of New Catalyst in Diesel Oil Hydrogenation Set

Supported NiW Catalysts with Tunable Size and Morphology of Active Phases for Highly Selective Hydrodesulfurization of Fluid Catalytic Cracking Naphtha

Regulating the crude oil–to–chemical process in a multizone fluidized bed reactor using unconventional catalyst formulations