Abstract:New developments in instrumentation for ocean environmental engineering are allowing unprecedented levels of trace contaminant measurement in the deep ocean. With funding from the U.S. National Science Foundation (NSF), our engineering design team constructed a new mass spectrometer-based in situ analysis system for work in the deep ocean environment over prolonged deployment periods. Our design goals were a depth capability of up to 4,000 m water depth (400 bars hydrostatic pressure) and autonomous operation for periods of up to six months to a year, depending upon the type of external battery system used or other deployment circumstances, e.g., availability of a power cable or fuel cell power source. We chose a membrane introduction mass spectrometry (MIMS) sampling approach, which allows for dissolved gases and volatile organics introduction into the mass spectrometer vacuum system. The MIMS approach and the hydrophobic, silicon-coated membrane chosen both draw upon our previous experience with this technology in the deep ocean. The membrane has been tested to 400 bars in a series of long-term hydrostatic pressure tests, which extend the 200-bar working depth rating of this membrane by a factor of 2. Long-term deployment capability of the moderately powered, approximately 100 W system, was accomplished by power management of the embedded computer system and custom electronics with Windows-based and custom software now fully-developed and bench tested. The entire system fits within a 6.5-inch outside diameter pressure housing that is approximately five feet long. It consists of a 1 to 200 amu range quadrupole mass spectrometer equipped with Faraday and electron multiplier detectors, compact turbo-molecular and backing diaphragm vacuum pumps, internal rechargeable batteries, and internal waste vacuum chamber. Sample routing past the MIMS is accomplished by computer-controlled solenoid valves. We designed the pressure housings of both 6AL4V and type 2 titanium alloys that are rated to working depths of >4,000 m and are essentially corrosion proof over long-term deployments. We designed and integrated a fail-safe valving system for both rapid response to high-pressure MIMS failure and a pressure-switch circuit and high-pressure solenoid valve to detect and protect against slow leaks of the MIMS. To route sample waters to the MIMS-based instrument, we also designed and built a rugged plastic plenum that couples to the face of the sampler head, the latter of which consists of the MIMS inlet and a full-ocean rated thermister temperature probe with an operational range from −5 to 50°C. These instrumentation innovations will be described in the paper.

An instrument for sampling water from the benthic boundary layer

An instrument system for monitoring and sampling suspended sediment in the benthic boundary layer

A routine device for high resolution bottom water sampling

A Pressure-Triggered Isobaric Sequential Liquid Sampling System for Full-Ocean-depth: Design and Field Deployment

A New Deep-Sea Gas-Tight Isobaric Water Sampler

An instrument to measure seabed boundary-layer processes

A large volume particulate and water multi-sampler with in situ preservation for microbial and biogeochemical studies

A Hybrid Lister‐Outrigger Probe for Rapid Marine Geothermal Gradient Measurement

BIOMAPER-II: an integrated instrument platform for coupled biological and physical measurements in coastal and oceanic regimes

A high-pressure serial sampler to measure microbial activity in the deep sea

A Deep-Ocean Mass Spectrometer to Monitor Hydrocarbon Seeps and Pipelines

New instrumentation for the investigation of sediment suspension processes in the shallow marine environment

Pressure-Retaining Sampler and High-Pressure Systems to Study Deep-Sea Microbes Under in situ Conditions

Development on a New Type of Marine Plankton Temperature-Retained and Pressure-Retained Sampler

A pressure-retaining deep ocean sampler and transfer system for measurement of microbial activity in the deep sea

The “Little MonSta” Deep-Sea Benthic, Precision Deployable, Multi-Sensor and Sampling Lander Array

Hydrothermal Organic Geochemistry (HOG) sampler for deployment on deep-sea submersibles

A novel design for sampling benthic zooplankton communities in disparate Gulf of Alaska habitats using an autonomous deep-water plankton pump

Half a cubic hectometer mooring array of 3000 temperature sensors in the deep sea

HALOBATES: An autonomous surface vehicle for high-resolution mapping of the sea-surface microlayer and near-surface layer on essential climate variables

Autonomous Targeted Sampling of the Deep Chlorophyll Maximum Layer in a Subtropical North Pacific Eddy