Abstract:New developments in instrumentation for ocean environmental engineering are allowing unprecedented levels of trace contaminant measurement in the deep ocean. With funding from the U.S. National Science Foundation (NSF), our engineering design team constructed a new mass spectrometer-based in situ analysis system for work in the deep ocean environment over prolonged deployment periods. Our design goals were a depth capability of up to 4,000 m water depth (400 bars hydrostatic pressure) and autonomous operation for periods of up to six months to a year, depending upon the type of external battery system used or other deployment circumstances, e.g., availability of a power cable or fuel cell power source. We chose a membrane introduction mass spectrometry (MIMS) sampling approach, which allows for dissolved gases and volatile organics introduction into the mass spectrometer vacuum system. The MIMS approach and the hydrophobic, silicon-coated membrane chosen both draw upon our previous experience with this technology in the deep ocean. The membrane has been tested to 400 bars in a series of long-term hydrostatic pressure tests, which extend the 200-bar working depth rating of this membrane by a factor of 2. Long-term deployment capability of the moderately powered, approximately 100 W system, was accomplished by power management of the embedded computer system and custom electronics with Windows-based and custom software now fully-developed and bench tested. The entire system fits within a 6.5-inch outside diameter pressure housing that is approximately five feet long. It consists of a 1 to 200 amu range quadrupole mass spectrometer equipped with Faraday and electron multiplier detectors, compact turbo-molecular and backing diaphragm vacuum pumps, internal rechargeable batteries, and internal waste vacuum chamber. Sample routing past the MIMS is accomplished by computer-controlled solenoid valves. We designed the pressure housings of both 6AL4V and type 2 titanium alloys that are rated to working depths of >4,000 m and are essentially corrosion proof over long-term deployments. We designed and integrated a fail-safe valving system for both rapid response to high-pressure MIMS failure and a pressure-switch circuit and high-pressure solenoid valve to detect and protect against slow leaks of the MIMS. To route sample waters to the MIMS-based instrument, we also designed and built a rugged plastic plenum that couples to the face of the sampler head, the latter of which consists of the MIMS inlet and a full-ocean rated thermister temperature probe with an operational range from −5 to 50°C. These instrumentation innovations will be described in the paper.

A pressure-retaining deep ocean sampler and transfer system for measurement of microbial activity in the deep sea

A Pressure-Triggered Isobaric Sequential Liquid Sampling System for Full-Ocean-depth: Design and Field Deployment

Pressure-Retaining Sampler and High-Pressure Systems to Study Deep-Sea Microbes Under in situ Conditions

A high-pressure serial sampler to measure microbial activity in the deep sea

MFPD: Multi-sequence Flow-through Pressure-retaining Sampler for Deep Sea Geofluid Research

A bacteriological pressure-retaining deep-sea sampler and culture vessel

A New Deep-Sea Gas-Tight Isobaric Water Sampler

A System For Deep-Sea Microbe Sediment Pressure-Retaining Sampling, Transfer And Incubation

Capturing Amphipods in the Mariana Trench with a Novel Pressure Retaining Sampler

Design of A Deep-ocean Sampling Device for Microorganisms with In-situ Filtration and Preservation

Design of Pressure Retention and Transfer System for Abyssal Sediments

A Deep-Ocean Mass Spectrometer to Monitor Hydrocarbon Seeps and Pipelines

A deep continental aquifer downhole sampler for microbiological studies

Microbial Activities in Undecompressed and Decompressed Deep-Seawater Samples

A novel submersible-mounted sediment pressure-retaining sampler at full ocean depth

Exploring the Deep Marine Biosphere: Challenges, Innovations, and Opportunities

Design and Experimental Study of a Novel Full-ocean-depth Pressure-retaining Sediment Sampler

A Pressure-Retaining Sampling Device for Deep-Sea Sediments

Design and study of a deep-sea multi-depth in-situ pore water pressure-retaining sampler

Autonomous Application of Quantitative PCR in the Deep Sea: In Situ Surveys of Aerobic Methanotrophs Using the Deep-Sea Environmental Sample Processor

A Pressure-Holding Sampling Device for Macro Organisms in Hadal Trenches