Abstract:Au-20Sn preforms such as microscale thin foils or wires can be widely used as lead-free solder in the high-power optoelectronics and hermetic sealing applications. However, as-cast Au-20Sn eutectic alloy with Au5Sn and AuSn phases is intrinsically brittle at room temperature due to limited slip systems associated with their complicated trigonal structure and hexagonal packed structure. In this study, we successfully made an Au-20Sn foil with thickness of 48 mu m by multi-pass hot rolling on as-cast alloy with an initial thickness of 4 mm. The microstructure, texture and recrystallization evolutions of the Au-20Sn eutectic alloy during hot rolling process were investigated in detail. The results indicated that plastic instability occurs in the eutectic lamellar structure when the nanoscale layers were subjected to the rolling strain, and promoted the microstructural spheroidization. Besides, the spheroidizing behavior in AuSn phase was found more preferential compared with that in the Au5Sn phase. After dynamic recrystallization, <0001>parallel to ND deformation texture was introduced in the AuSn phase while <0001>parallel to TD deformation texture was formed in the Au5Sn phase. These phenomena were attributed to the difference in slip systems activated in the two phases associated with their different c/a ratios. A transition of dynamic recrystallization mechanism from the initial lamellar phase to the later equiaxed phase (in other words, from continuous dynamic recrystallization mechanism to discontinuous dynamic recrystallization) was observed, as evidenced by the evolutions of in-grain misorientation accumulation and grain boundary migration. Additionally, an interesting recrystallization phenomenon occurred that the AuSn grains could nucleate in the Au5Sn phase during hot rolling, which was considered as a strain induced phase decomposition behavior. The present studies can provide insight into understanding microstructural evolution of Au-20Sn eutectic alloy during hot rolling, which enables a further optimization of processing parameters to fabricate Au-20Sn alloy foils with desired microstructure and properties. (C) 2020 Elsevier B.V. All rights reserved.

Hot deformation behavior and related microstructure evolution in Au−Sn eutectic multilayers

Microstructure Evolution and Deformation Behavior of Au–20Sn Eutectic Alloy During Hot Rolling Process

Plastic Instability and Spheroidization in a Nanolayered Au-20Sn Alloy During the Hot Rolling Process

Atomic-level Study of AuSn–Au5Sn Eutectic Interfaces

Hot Deformation Behavior and Microstructure Evolution of High-Strength Al-Zn-Mg-Cu Alloy

Microstructure Evolution and Hot Deformation Behavior of a CuNiSn Alloy

Microstructures and mechanical properties of Cu-Sn alloy subjected to elevated-temperature heat deformation

Microstructure evolution, constitutive modeling and forming simulation of AA6063 aluminum alloy in hot deformation

Hot compressive deformation of eutectic Al-17at% Cu alloy on the interface of the Cu-Al composite plate produced by horizontal continuous casting

Dynamic microstructural evolution of Al-Cu-Li alloys during hot deformation

Revealing the Microstructure Evolution Mechanism and Mechanical Responses of a Novel Al–Zn–Mg–Cu Alloy by Hot Deformation Process

Hot Deformation Behavior and Microstructure Evolution of the Spray Deposited and Secondary Hot Extruded 2195 Al–Li Alloy

The Deformation Behavior and Microstructure Evolution of a Mn- and Cr-Containing Al-Mg-Si-Cu Alloy During Hot Compression and Subsequent Heat Treatment

Hot Deformation Behavior of Cu–Sn–La Polycrystalline Alloy Prepared by Upcasting

The hot deformation characteristics and the associated microstructural evolution of an Al-Cu-Li-Zn alloy studied by constitutive equations and processing maps

The role of Sn element on the deformation mechanism and precipitation behavior of the Al–Cu–Mg alloy

Microstructure evolution and mechanical responses of Al–Zn–Mg–Cu alloys during hot deformation process

Microstructural evolution, flow stress and constitutive modeling of Al−1.88Mg−0.18Sc−0.084Er alloy during hot compression

Hot Workability and Microstructure Evolution of Homogenized 2050 Al-Cu-Li Alloy during Hot Deformation

Microstructure characterization and dynamic recrystallization behavior of Ni–Cu alloy during hot deformation

Uncovering Microstructure Evolution and Dynamic Softening Mechanism of Spray-Deposited AlZnMgCu Alloy Under Thermal Deformation