Abstract:Aerodynamic cooling of hot components/surfaces such as those encountered in gas turbine engines is needed to avoid premature failure of parts due to thermo-mechanical stresses. An effective way of achieving this cooling is through the exchange of heat via effusion/film cooling holes on the hot surfaces. The gases absorb heat as they flow through the cooling holes and also by forming a protective layer of relatively cool gases near the hot surface. Modeling these processes allow for durable design of components and computational simulations offer a complementary way to design new parts or enable performance assessment of the existing parts at new operating conditions. However, in order to perform numerical simulations of heat transfer through effusion holes, the heat conduction through the solid liner and the convection from the gas phase must be coupled considering all the relevant length and time scales. The time scale separation between the solid and the gas phase makes this prohibitively expensive for large scale computations. In applications involving hundreds of effusion holes, resolving the geometry of each effusion hole along with the primary flow (with typically larger length scales) is very challenging. In the current work, we overcome the difficulties associated with the resolution of cooling holes by employing a local source method (Andreini et al, J. Eng. Gas Turb. Power, 2014) to model the heat transfer to the walls. This method is assessed in a canonical configuration based on experiments performed by Gustafsson (Gustaffson, Ph.D. Thesis, 2001).Large Eddy Simulations (LES) coupled with conjugate heat transfer (CHT) models are used in this study. Simulations that resolve the flow passages explicitly using mesh both in the fluid and the solid domains, were used to validate the fidelity of grid resolution, turbulence models and other simulation parameters in predicting velocity fields and wall temperature data. Although, resolving all the effusions passages provides the most accurate results, it is not practical in real applications. Hence, a local source model is employed to model the heat transfer that happens in the cooling-hole passages. In this method, the effusion passage is not resolved (using a mesh) and the mass transfer across the cooling hole passage is prescribed as an injection-extraction boundary condition. The heat transfer at the fluid-solid interface of the cooling-hole passage is also modeled based on Nusselt number correlations available in the literature. This modeling procedure enables simulations with flexible mesh topologies that can be generated at a relatively low cost in comparison to the fully resolved mesh configurations. The local source method is assessed and validated using the available experimental data. The results show that the meshes which resolve the penetration depth in the solid and which conform at the solid-gas interface provide better prediction of the wall temperatures.

Analyzing metal material cooling intensity: A method for obtaining heat transfer coefficients

The effect of laminar cooling heat transfer coefficient on the temperature field of steel plate

A symplectic analytical approach for thermal-metallurgical coupling problems: A case study of hot-rolled coil cooling

Study of Flow and Heat Transfer in High Pressure Die Casting Cooling Channel

Numerical investigation of laminar flow and heat transfer in a liquid metal cooled mini-channel heat sink

The Measurement and Calculation of Heat Transfer Coefficient under Different Cooling Conditions

The Efficient Way to Design Cooling Sections for Heat Treatment of Long Steel Products

Robust methodology for determination of heat transfer coefficient distribution in convection

A Computational Study of the Blast Furnace Cooling Stave Based on the Analysis of Heat Transfer

Modeling Effusion Cooling And Conjugate Heat Transfer Using Local Source Method

Conjugated Heat Transfer Analysis Of A Film Cooling Passage With Different Rib Configurations

Model experiments for the determination of the heat-transfer coefficient and transition thermal analysis in the direct rolling process

Conjugate Heat Transfer Analysis of Film Cooling Flows

Determination of Heat Transfer Coefficient for Air-Atomized Water Spray Cooling and Its Application in Modeling of Thermomechanical Controlled Processing of Die Forgings

Experimental Investigation of Interfacial Thermal Conductance for Molten Metal Solidification on A Substrate

Performance Analysis and Structural Optimization of a Finned Liquid-Cooling Radiator for Chip Heat Dissipation

Comparative study of heat transfer in a mini/micro pipe with water and liquid metal as fluid

Numerical Investigation on Mechanism of Heat Transfer Augmentation in Lamilloy

Heat Transfer Coefficient Determination in a Gravity Die Casting Process with Local Air Gap Formation and Contact Pressure Using Experimental Evaluation and Numerical Simulation

Metallurgical Method of Determining Heat Transfer Coefficient in Simulations of Twin-Roll Casting

Quantitative and Qualitative Analysis of Advanced Aluminum Composites for Heat Transfer Properties