Abstract:Roughly 75% of the cost for Lithium ion batteries are attributed to material cost for electrodes, electrolyte and separator. Furthermore, the production cost of the cathode material is responsible for >50% of the overall material cost. Therefore, technological breakthroughs for an increased energy density and decreased production cost along the whole battery value chain are urgently needed. State of the art (SOTA) cathode active materials (CAMs) are LiFePO 4 (LFP) and layered oxides such as LiNi 1-x-y Co x Mn y O 2 (NCM). By increasing the Ni content within NCM materials, the discharge capacity and therefore the energy density on material level can be gradually increased. Since a higher Ni content (>80% Ni) in NCM ́s implicitly entails several challenges with respect to the material synthesis procedure, stability during electrode processing as well as life time, the broad commercialization of these CAMs still needs further advances. Aqueous processing of Ni-rich layered oxide cathode materials is a promising approach to simultaneously decrease electrode manufacturing costs, while bringing environmental benefits by substituting the SOTA, often toxic and expensive organic processing solvents. Furthermore, recycling of batteries and especially of the cathode material, will probably become an important topic in the coming years. The conversion of electrodes into black mass might be cheaper and easier for aqueously-processed cathodes ( e . g ., by using fluorine-free binders). However, an aqueous environment still remains challenging due to the high reactivity of Ni-rich layered oxides towards moisture, leading to surface reconstruction, lithium leaching and Al current collector corrosion due to the resulting high pH value of the aqueous electrode paste. Common approaches to suppress current collector corrosion are the protection of the Al current collector by a carbon coating or decreasing the pH value by using dilute acids. The latter approach, especially with phosphoric acid, might lead to formation of a phosphate coating at the surface of cathode particles, which is able to protect the NCM against further degradation. Herein, we present a facile method to enable aqueous processing of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) by the addition of lithium sulphate (Li 2 SO 4 ) during electrode paste dispersion. The aqueously-processed electrodes retain 80% of their initial capacity after 400 cycles in NCM811 || graphite full-cells, while electrodes processed without the addition of Li 2 SO 4 reach 80% of their capacity after only 200 cycles. Furthermore, with regard to electrochemical performance, aqueously-processed electrodes using carbon-coated Al current collector outperform reference electrodes, based on SOTA production processes involving N -methyl-2-pyrrolidone as processing solvent and fluorinated binders. The positive impact on cycle life by the addition of Li 2 SO 4 stems from a formed sulphate coating, protecting the NCM811 surface against degradation. Results reported herein open a new avenue for the processing of Ni-rich NCM electrodes using more sustainable aqueous routes. Figure 1

Influence of Phosphate Surface Coating on Performance of Aqueous‐Processed NMC811 Cathodes in 3 Ah Lithium‐Ion Cells

Surface Coating of NCM-811 Cathode Materials with G-C3n4 for Enhanced Electrochemical Performance.

Facile Surface Coatings for Performance Improvement of NMC811 Battery Cathode Material

Improvement of the Electrochemical Performance of LiNi 0.8 Co 0.1 Mn 0.1 O 2 via Atomic Layer Deposition of Lithium-Rich Zirconium Phosphate Coatings

Enabling Aqueous Processing of Ni-Rich Layered Oxide Cathode Materials by Using Lithium Sulphate as Processing Additive

Advancing Lithium-Ion Batteries' Electrochemical Performance: Ultrathin Alumina Coating on Li(Ni0.8Co0.1Mn0.1)O2 Cathode Materials

Concerted Effect of Ion- and Electron-Conductive Additives on the Electrochemical and Thermal Performances of the LiNi0.8Co0.1Mn0.1O2 Cathode Material Synthesized by a Taylor-Flow Reactor for Lithium-Ion Batteries

In-situ Formation of Hybrid Li3PO4-AlPO4-Al(PO3)3 Coating Layer on LiNi0.8Co0.1Mn0.1O2 Cathode with Enhanced Electrochemical Properties for Lithium-Ion Battery

Wet-Chemical Synthesis of a Protective Coating on NCM111 Cathode: The Quantified Effects of Washing, Sintering and Coating

Stabilizing Nickel‐Rich Cathodes in Aqueous Process through Nanocellulose as Water Barrier

Improving the Performance of LiNi0.9Co0.05Mn0.05O2 via Atomic Layer Deposition of ZnxOy Coating

Increased Performance Improvement of Lithium-Ion Batteries by Dry Powder Coating of High-Nickel NMC with Nanostructured Fumed Ternary Lithium Metal Oxides

Lithium Phosphonate Functionalized Polymer Coating for High‐Energy Li[Ni 0.8 Co 0.1 Mn 0.1 ]O 2 with Superior Performance at Ambient and Elevated Temperatures

Study of degradation mechanisms in aqueous-processed Ni-rich cathodes for Enhanced Sustainability of Batteries

Stabilized Positive Electrode Material to Enable High Energy/Power Density Lithium-Ion Batteries

High-performance LiNi0.8Mn0.1Co0.1O2 cathode by nanoscale lithium sulfide coating via atomic layer deposition

Influence of Process Conditions During Aqueous and Direct Recycling of NMC811 Cathodes

Nonsacrificial Nitrile Additive for Armoring High-Voltage LiNi0.83 Co0.07 Mn0.1 O2 Cathode with Reliable Electrode-Electrolyte Interface toward Durable Battery.

Synthesis of Single Crystalline Ni-Rich NMC811 Cathode Materials and Improved Performance Enabled By Ultrathin Surface Coating Layer

Optimized structure stability and cycling performance of LiNi0.8Co0.1Mn0.1O2 through homogeneous nano-thickness Al2O3 coating

Carbonized Polymer Dots Enhancing Interface Stability of LiNi0.8Co0.1Mn0.1O2 Cathodes