Abstract:Pyrolysis catalysis is a promising method for converting waste plastics into high-value products from both economic and environmental perspectives. A low-cost catalyst is crucial for the batch treatment of waste plastics. In this study, a novel nickel catalyst based on coal gangue was prepared by impregnation. The catalyst is not only inexpensive, but also exhibits excellent catalytic performance in the pyrolysis of plastics. Polyethylene was pyrolyzed in a two-stage fixed-bed reactor to produce carbon nanotubes and hydrogen. The effects of catalytic temperatures on the production of hydrogen and carbon nanotubes from the catalyst were investigated. The maximum concentration and yield of hydrogen were 66.48 vol.% and 31.48 mmol/gplastic at 750 °C. Various techniques were used to fully characterize the carbon deposition, such as electron microscopy, temperature programmed oxidation, X-ray diffraction and Raman spectroscopy. The results showed when the catalytic temperature is 800 °C, the graphitization degree of obtained carbon was higher and the defects was fewer. The Raman IG/ID of the product was 0.72, which exceeded the graphitization of many industrially synthesized carbon nanotubes. It is also found that the catalytic temperature was very important for the hydrogen yield and the growth of carbon nanotubes. The temperature is too low, the catalyst activity is insufficient. If the temperature was too high, the metal particles in the catalyst would agglomerate, resulting in the reduction of the catalyst active site and catalyst deactivation. Therefore, it is necessary to select a suitable temperature to achieve the co-production of hydrogen and carbon nanotubes from waste plastics. This study provides a new and effective way for the catalytic pyrolysis of waste plastics and the comprehensive utilization of coal gangue.

Catalytic Synthesis of Carbon Nanotubes and Hydrogen Gas from Waste Plastics Using LaNiO 3 Perovskite Catalyst

Catalytic Synthesis of Carbon Nanotubes and Hydrogen Gas from Waste Plastics Using LaNiO3 Perovskite Catalyst

Enhancement of hydrogen and carbon nanotubes production from hierarchical Ni/ZSM-5 catalyzed polyethylene pyrolysis

The Production of Carbon Nano-Onions and Wheat Stalk Nano-Chains over Stainless Steel Supported La0.95mg0.05ni0.8co0.2o3 Catalyst

Carbon nanotubes from post-consumer waste plastics: Investigations into catalyst metal and support material characteristics

Preparation of high quality carbon nanotubes by catalytic pyrolysis of waste plastics using FeNi-based catalyst

Co-production of Hydrogen and Carbon Nanotubes from Real-World Waste Plastics: Influence of Catalyst Composition and Operational Parameters

A Novel Nickel Catalyst Supported on Coal Gangue for Producing Hydrogen and Carbon Nanotubes from Waste Plastics

Carbon nanotubes production from catalytic pyrolysis of polyethylene over nickel-based catalysts: The influence of support materials

Production of Carbon Nanotubes Via Catalytic Pyrolysis of Waste Plastics over Ni/Al2O3 Catalyst: the Influence of Plastic Types

Investigation of spherical alumina supported catalyst for carbon nanotubes production from waste polyethylene

Production of carbon nanotubes via catalytic pyrolysis of waste plastics over Ni/Al 2 O 3 catalyst: The influence of plastic types

Production of carbon nanotubes via catalytic pyrolysis of polyethylene over Ni/ZSM-5 prepared by ethylene glycol assisted impregnation

In-situ exsolution of Fe-Ni alloy catalysts for H2 and carbon nanotube production from microwave plasma-initiated decomposition of plastic wastes

Fabrication of Fe-Zr, Co-Zr, and Ni-Zr Catalysts to Boost CNTs Synthesis from Plastic Wastes and the Electrocatalytic Oxygen Evolution Reaction

Preparation of High-Value Carbon Nanotubes from Real Waste Plastic Towards the Negative Carbon Technology

Temperature-dependent highly active LaCaMgAl2O4 catalyst effect on carbon nanomaterial and hydrogen generation from polymethyl methacrylate plastic

Co-production of hydrogen and carbon nanotubes from catalytic pyrolysis of waste plastics on Ni-Fe bimetallic catalyst

Co-production of Hydrogen and Carbon Nanotubes Via Catalytic Pyrolysis of Polyethylene over Fe/ZSM-5 Catalysts: Effect of Fe Loading on the Catalytic Activity

CO2-mediated Catalytic Upcycling of Plastic Waste for H2-rich Syngas and Carbon Nanomaterials.

Innovative Carbon Nanotubes-Bridging Strategy Valorizes Plastic Waste into High-Quality H2-rich Syngas While Suppressing CO2 Emissions