Three-dimensional printing of functionally graded liquid crystal elastomer

Zijun Wang,Zhijian Wang,Yue Zheng,Qiguang He,Yang Wang,Shengqiang Cai

DOI: https://doi.org/10.1126/sciadv.abc0034

IF: 13.6

2020-09-25

Science Advances

Abstract:A 3D printing strategy to fabricate functionally graded liquid crystal elastomer is developed.

multidisciplinary sciences

What problem does this paper attempt to address?

3D Printing of Reprogrammable Liquid Crystal Elastomers with Exchangeable Boronic Ester Bonds

Xinzi Yu,Changyue Liu,Liqian Wang,Tianyu Li,Lingxin Yuan,Jiping Yang,Rui Xiao,Zhijian Wang

DOI: https://doi.org/10.1016/j.giant.2024.100331

2024-01-01

Giant

Abstract:Liquid crystal elastomers (LCEs) are a kind of soft actuating materials with large reversible deformation ability, which can work as the “motor” to exhibit complex deformations and drive the locomotion of soft robots. The deformation of LCEs depends on the three-dimensional (3D) shape of whole structure and alignment patterns of mesogens. Various methods have been employed to fabricate the LCE structure with desired shapes and mesogen alignments. However, conventional 3D printed LCEs require continuous thermal energy input to maintain their actuated shapes. The LCEs cannot be reprocessed and reprogrammed once cured. Herein, we introduce dynamic boronic ester bonds into the ink, with which the printed LCE structures are capable of being reprogrammed from polydomain into monodomain state and vice versa. We further explore the effects of printing parameters and content of dynamic covalent bonds on the actuation performance and reprogramming ability. The actuated shape could be well predicted with finite element method. The dynamic printable LCEs developed here offer new strategy and large design space for LCE structures.
Shape Memory Behaviors of 3D Printed Liquid Crystal Elastomers

Lu Dai,Liqian Wang,Baihong Chen,Zengting Xu,Zhijian Wang,Rui Xiao

DOI: https://doi.org/10.20517/ss.2022.28

2023-01-01

Soft Science

Abstract:As soft active materials, shape-memory polymers (SMPs) and liquid crystal elastomers (LCEs) have attracted considerable research interest due to their potential applications in various areas. SMPs refer to polymeric materials that can return to their permanent shape in response to external stimuli, such as heat, light, and solvent. In this sense, LCEs can exhibit intrinsic shape-memory behaviors since LCEs can switch between two shapes with temperature change due to the order-disorder transition of liquid crystals. In this work, we fabricate both the polydomain and monodomain nematic LCEs through direct ink writing 3D printing. With increasing the temperature of the substrates, the printed LCEs change from the monodomain state to the polydomain state. For polydomain LCEs, a reversible shape change can occur upon constant loading, while the monodomain can switch the shape with temperature in the stress-free state. This two-way shape-memory behavior is caused by the nematic-isotropic phase transition. We further show that the printed LCEs exhibit a good one-way shape-memory effect due to glass transition. The shape recovery region increases with the programming temperature, which is a typical temperature memory effect. Finally, it is demonstrated that complex shape-memory performance can be designed by combining one-way and two-way shape-memory effects. Specifically, for the monodomain LCEs, with increasing temperature, the programmed shape first recovers, and a second shape change can further occur due to the nematic-isotropic transition.
4D Printing of Freestanding Liquid Crystal Elastomers via Hybrid Additive Manufacturing (Adv. Mater. 39/2022)

Xirui Peng,Shuai Wu,Xiaohao Sun,Liang Yue,S. Macrae Montgomery,Frédéric Demoly,Kun Zhou,Ruike Renee Zhao,H. Jerry Qi

DOI: https://doi.org/10.1002/adma.202270272

IF: 29.4

2022-10-02

Advanced Materials

Abstract:4D Printing In article number 2204890, Ruike Renee Zhao, H. Jerry Qi, and co‐workers report a hybrid 4D printing method to fabricate freestanding liquid crystal elastomers "on‐the‐fly" by using laser‐assisted direct ink writing. This process is integrated with Digital Light Processing for printing optional structural or sacrificial materials to create active architectures, such as active tensegrities, loading‐bearing actuators, and 3D liquid crystal lattices, in a one‐step additive process.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Microfluidic 3D Printing of Emulsion Ink for Engineering Porous Functionally Graded Materials

Martina Marcotulli,Maria Celeste Tirelli,Marina Volpi,Jakub Jaroszewicz,Chiara Scognamiglio,Piotr Kasprzycki,Karol Karnowski,Wojciech Święszkowski,Giancarlo Ruocco,Marco Costantini,Gianluca Cidonio,Andrea Barbetta

DOI: https://doi.org/10.1002/admt.202201244

IF: 6.8

2022-12-06

Advanced Materials Technologies

Abstract:Nowadays, soft functionally graded materials are highly desirable for a number of biomedical applications. However, their synthesis remains challenging due to inherent processability issues. Here, a microfluidic‐assisted multi‐material 3D printing strategy combined with a suspension bath is reported to tackle this challenge. Through the proposed approach, one can fabricate 3D complex architectures comprising high‐resolution spatial density and chemical composition gradients. In the last decade, 3D printing systems have greatly evolved both in terms of processable materials and printing resolutions, becoming a top seed technology for many academic and industrial applications. Nevertheless, manufacturing polymeric materials characterized by a trabecular porosity and functionally graded architecture—where both the local porosity and chemical composition of the matrix change in the 3D space—through additive platforms remains an open technical challenge. In this study, a 3D extrusion printing strategy to tackle this problem is presented. The proposed systems are based on a flow‐focusing microfluidic printing head—to continuously generate oil‐in‐water emulsion inks—and on an agarose fluid–gel used as a temporary support bath for the deposition of the photo‐curable emulsion inks. It is demonstrated that through this strategy one can design a priori and build with high accuracy both discontinuous and continuous functionally graded polymeric foams, where both the density and composition of the materials could be varied independently within arbitrarily complex 3D architectures. This study provides new means for the synthesis of microporous, polymeric FGMs which could find applications ranging from interface tissue engineering to automotive and construction industries.

materials science, multidisciplinary
4D Printing of High-Performance Thermal-Responsive Liquid Metal Elastomers Driven by Embedded Microliquid Chambers

Lu-Yu Zhou,Jiang-Hao Ye,Jian-Zhong Fu,Qing Gao,Yong He

DOI: https://doi.org/10.1021/acsami.9b22433

2020-03-11

Abstract:Four-dimensional (4D) printing of swellable materials have been viewed as an ideal approach to build shape morphing architectures. However, there is less variety in high-performance swellable materials, limiting its development. To address this challenge, we proposed a new strategy for designing high-performance thermal-responsive swellable materials. The reversible liquid-vapor phase change of embedded low boiling point liquid chambers and functional liquid metal fillers endows the designed elastomer with the reversible thermal-responsive swellable property with high stability, fast response speed, and large equilibrium deformation. Notably, liquid metal fillers play a crucial role in improving the thermal-responsive property via improving the thermal conductivity and fracture toughness and decreasing the stiffness. To demonstrate the feasibility of constructing shape morphing architectures with proposed thermal-responsive liquid metal elastomers, typical bilayer structures were printed and investigated. By altering the key design parameters, the response speed and equilibrium deformation can be adjusted as needed. Therefore, complex shape morphing architectures can be printed. This study could provide a new avenue to design swellable material systems for 4D printing of shape morphing architectures.
Advances in 4D printing of liquid crystalline elastomers: materials, techniques, and applications

Zhecun Guan,Ling Wang,Jinhye Bae

DOI: https://doi.org/10.1039/d2mh00232a

2022-07-04

Abstract:Liquid crystalline elastomers (LCEs) are polymer networks exhibiting anisotropic liquid crystallinity while maintaining elastomeric properties. Owing to diverse polymeric forms and self-alignment molecular behaviors, LCEs have fascinated state-of-the-art efforts in various disciplines other than the traditional low-molar-mass display market. By patterning order to structures, LCEs demonstrate reversible high-speed and large-scale actuations in response to external stimuli, allowing for close integration with 4D printing and architectures of digital devices, which is scarcely observed in homogeneous soft polymer networks. In this review, we collect recent advances in 4D printing of LCEs, with emphases on synthesis and processing methods that enable microscopic changes in the molecular orientation and hence macroscopic changes in the properties of end-use objects. Promising potentials of printed complexes include fields of soft robotics, optics, and biomedical devices. Within this scope, we elucidate the relationships among external stimuli, tailorable morphologies in mesophases of liquid crystals, and programmable topological configurations of printed parts. Lastly, perspectives and potential challenges facing 4D printing of LCEs are discussed.
Three-Dimensional Coprinting Of Liquid Metals For Directly Fabricating Stretchable Electronics

Yong He,Luyu Zhou,Junfu Zhan,Qing Gao,Jianzhong Fu,Chaoqi Xie,Haiming Zhao,Yu Liu

DOI: https://doi.org/10.1089/3dp.2017.0147

IF: 5.355

2018-01-01

3D Printing and Additive Manufacturing

Abstract:It is a significant challenge to fabricate functional stretchable electronics by directly printing Ga-based liquid metals (GLMs) due to their high surface tension. In this study, a coprinting method is developed, in which GLMs are printed together with elastic materials to overcome their poor printability. The continuous contact and extrusion of the external highly viscous elastic materials with its internal liquid metal inhibits the balling of liquid metal, achieving the liquid metal three-dimensional (3D) printing successfully. A multifunctional stretchable inductance sensor was 3D printed at the first time. This sensor can be used to test axial stretch, deflection, and radial stretch, allowing tracking of the status of soft snake structures such as the end executor of endoscope and fingers.
3D Printing of Near-Ambient Responsive Liquid Crystal Elastomers with Enhanced Nematic Order and Pluralized Transformation

Dongxiao Li,Yuxuan Sun,Xingjian Li,Xingxiang Li,Zhengqing Zhu,Boxi Sun,Shutong Nong,Jiyang Wu,Tingrui Pan,Weihua Li,Shiwu Zhang,Mujun Li

2024-11-11

Abstract:Liquid Crystal Elastomers with near-ambient temperature-responsiveness (NAT-LCEs) have been extensively studied for building bio-compatible, low-power consumption devices and robotics. However, conventional manufacturing methods face limitations in programmability (e.g., molding) or low nematic order (e.g., DIW printing). Here, a hybrid cooling strategy is proposed for programmable 3D printing of NAT-LCEs with enhanced nematic order, intricate shape forming, and morphing capability. By integrating a low-temperature nozzle and a cooling platform into a 3D printer, the resulting temperature field synergistically facilitates mesogen alignment during extrusion and disruption-free UV cross-linking. This method achieves a nematic order 3000% higher than those fabricated using traditional room temperature 3D printing. Enabled by shifting of transition temperature during hybrid cooling printing, printed sheets spontaneously turn into 3D structures after release from the platform, exhibiting bidirectional deformation with heating and cooling. By adjusting the nozzle and plate temperatures, NAT-LCEs with graded properties can be fabricated for intricate shape morphing. A wristband system with enhanced heart rate monitoring is also developed based on 3D-printed NAT-LCE. Our method may open new possibilities for soft robotics, biomedical devices, and wearable electronics.

Soft Condensed Matter,Human-Computer Interaction
Programmable 3D Shape-Change Liquid Crystalline Elastomer Based on a Vertically Aligned Monodomain with Cross-link Gradient

Jun Hu,Ze-Yang Kuang,Lei Tao,Yi-Fei Huang,Qing Wang,He-Lou Xie,Jiu-Ren Yin,Er-Qiang Chen

DOI: https://doi.org/10.1021/acsami.9b17393

2019-12-26

Abstract:A liquid crystalline elastomer (LCE) as a kind of stimuli-responsive materials, which can be fabricated to present the three-dimensional (3D) change in shape, shows a wide range of applications. Herein, we propose a simple and robust way to prepare a 3D shape-change actuator based on gradient cross-linking of the vertically aligned monodomain of liquid crystals (LCs). First, gold nanoparticles grafted by liquid crystalline polymers (LCPs) are used to induce the homeotropic orientation of the LC monomer and cross-linkers. Then, photopolymerization under UV irradiation is carried out, which can result in the LCE film with a cross-link gradient. Different from the typical LCEs with homogenous alignment that usually show the shape change of extension/contraction, the obtained vertically aligned LCE film exhibits excellent bendability under a thermal stimulus. The nanoindentation experiment demonstrates that the deformation of LCE films comes from the difference in Young's modulus on two sides of the thin film. Simply scissoring the thin film can prepare the samples with different bending angles under the fixed length. Moreover, using a photomask to pattern the film during photopolymerization can realize the complex 3D deformation, such as bend, fold, and buckling. Further, the patterned LCE film doped with multiwalled carbon nanotubes modified by LCPs (CNT-PDB) can act as a light-fueled microwalker with fast crawl behavior.
Programmable spatial deformation by controllable off-center freestanding 4D printing of continuous fiber reinforced liquid crystal elastomer composites

Qingrui Wang,Xiaoyong Tian,Daokang Zhang,Yanli Zhou,Wanquan Yan,Dichen Li

DOI: https://doi.org/10.1038/s41467-023-39566-3

IF: 16.6

2023-06-30

Nature Communications

Abstract:Owing to their high deformation ability, 4D printed structures have various applications in origami structures, soft robotics and deployable mechanisms. As a material with programmable molecular chain orientation, liquid crystal elastomer is expected to produce the freestanding, bearable and deformable three-dimensional structure. However, majority of the existing 4D printing methods for liquid crystal elastomers can only fabricate planar structures, which limits their deformation designability and bearing capacity. Here we propose a direct ink writing based 4D printing method for freestanding continuous fiber reinforced composites. Continuous fibers can support freestanding structures during the printing process and improve the mechanical property and deformation ability of 4D printed structures. In this paper, the integration of 4D printed structures with fully impregnated composite interfaces, programmable deformation ability and high bearing capacity are realized by adjusting the off-center distribution of the fibers, and the printed liquid crystal composite can carry a load of up to 2805 times its own weight and achieve a bending deformation curvature of 0.33 mm −1 at 150 °C. This research is expected to open new avenues for creating soft robotics, mechanical metamaterials and artificial muscles.

multidisciplinary sciences
Grayscale digital light processing 3D printing for highly functionally graded materials

Xiao Kuang,Jiangtao Wu,Kaijuan Chen,Zeang Zhao,Zhen Ding,Fengjingyang Hu,Daining Fang,H. Jerry Qi

DOI: https://doi.org/10.1126/sciadv.aav5790

IF: 13.6

2019-05-03

Science Advances

Abstract:We present a single-vat grayscale digital light processing 3D printing method for highly functionally graded materials.

multidisciplinary sciences
Digital Light Processing-Based 3D Printing of Cell-Seeding Hydrogel Scaffolds with Regionally Varied Stiffness

Dai Xue,Jiaxin Zhang,Yancheng Wang,Deqing Mei

DOI: https://doi.org/10.1021/acsbiomaterials.9b00696

2019-01-01

ACS Biomaterials Science & Engineering

Abstract:Cell-seeding heterogeneous scaffolds with regionally varied stiffness play an important role in tissue engineering, e.g., bone and cartilage regeneration, that require the recapitulation of geometric complexity through biocompatible material to mimic the natural cell microenvironment in vivo. Here, we report the digital light processing (DLP)-based 3D printing of cell-seeding hydrogel scaffold with regionally varied stiffness by tuning the exposure time without changing the geometric architecture. Mechanical tests on printed poly(ethylene glycol) diacrylate (PEGDA) hydrogels homogeneous scaffold revealed that a 60% increase in the elastic modulus can be achieved by setting the optimal exposure time. Furthermore, regulating the stiffness by varying the exposure time was demonstrated in the printed three-sectional heterogeneous scaffolds. Uniaxial compression tests showed that no fracture was observed even when the compression strain reached up to 25%, indicating that by adjusting the exposure time, the undesired influence of the scaffold on mechanical integrity could be avoided. 3T3 fibroblasts were then seeded onto the scaffold, and the biocompatibility together with the physical support of the scaffolds were confirmed by observation and cell population assessment.
Guided Folding of Nematic Liquid Crystal Elastomer Sheets into 3D via Patterned 1D Microchannels

Yu Xia,Gerardo Cedillo‐Servin,Randall D. Kamien,Shu Yang,Gerardo Cedillo-Servin

DOI: https://doi.org/10.1002/adma.201603751

IF: 29.4

2016-09-15

Advanced Materials

Abstract:Two-dimensional liquid-crystal elastomer (LCE) sheets with preprogrammed topological defects are prepared by aligning liquid-crystal monomers within micropatterned epoxy channels, followed by photopolymerization. Upon heating, the LCE films form various three-dimensional structures in agreement with theoretical design. The miniaturized LCE actuators offer large-area work capacities (≈1.05 J m<sup>-2</sup> ) to lift over 700 times their own weight.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Fast Digital Patterning of Surface Topography Toward Three-Dimensional Shape-Changing Structures

Zhou Chen,Changhong Linghu,Kaixin Yu,Jinye Zhu,Hongyu Luo,Chenghao Qian,Yin Chen,Yipu Du,Shun Zhang,Jizhou Song

DOI: https://doi.org/10.1021/acsami.9b17343

IF: 9.5

2019-01-01

ACS Applied Materials & Interfaces

Abstract:Exiting strategies for 3D shape-changing structures are constrained by either the complicated fabrication process or the harsh demands of active materials. Facile preparation of 3D shape-changing structures with an extremely simple approach based on the elastomeric polymer still remains a challenging topic. Here, we report a fast digital patterning of surface topography of a single-layer elastomeric polymer toward 3D shape-changing structures. The surface topography features digitally engraved grooves by a laser engraver on a poly(dimethylsiloxane) (PDMS) sheet, which is surface oxidized by the UV-ozone treatment. The resulting engraved PDMS sheets exhibit programmable shape-changing behaviors to form various 3D structures under the action of organic solvent. Experimental and numerical studies reveal the fundamental aspects of surface topography-guided 3D shape-changing structures. Demonstrations of this concept in developing various complex 3D shape-changing structures illustrate the simplicity and effectiveness of our approach, thereby creating engineering opportunities in a wide range of applications such as actuators and soft robots.
High-precision 3D printing of multi-branch vascular scaffold with plasticized PLCL thermoplastic elastomer

Yunda Han,Heran Wang,Yuheng Guan,Song Li,Zewei Yuan,Lihua Lu,Xiongfei Zheng

DOI: https://doi.org/10.1088/1748-605X/ad407c

2024-04-30

Abstract:Three-dimensional (3D) printing has emerged as a transformative technology for tissue engineering, enabling the production of structures that closely emulate the intricate architecture and mechanical properties of native biological tissues. However, the fabrication of complex microstructures with high accuracy using biocompatible, degradable thermoplastic elastomers poses significant technical obstacles. This is primarily due to the inherent soft-matter nature of such materials, which complicates real-time control of micro-squeezing, resulting in low fidelity or even failure. In this study, we employ Poly (L-lactide-co-ϵ-caprolactone) (PLCL) as a model material and introduce a novel framework for high-precision 3D printing based on the material plasticization process. This approach significantly enhances the dynamic responsiveness of the start-stop transition during printing, thereby reducing harmful errors by up to 93%. Leveraging this enhanced material, we have efficiently fabricated arrays of multi-branched vascular scaffolds that exhibit exceptional morphological fidelity and possess elastic moduli that faithfully approximate the physiological modulus spectrum of native blood vessels, ranging from 2.5 to 45 MPa. The methodology we propose for the compatibilization and modification of elastomeric materials addresses the challenge of real-time precision control, representing a significant advancement in the domain of melt polymer 3D printing. This innovation holds considerable promise for the creation of detailed multi-branch vascular scaffolds and other sophisticated organotypic structures critical to advancing tissue engineering and regenerative medicine.
A Molecular Rheology Dynamics Study on 3D Printing of Liquid Crystal Elastomers

Senay Ustunel,Harsh Pandya,Marianne E. Prévôt,Gisele Pegorin,Faeze Shiralipour,Rajib Paul,Robert J. Clements,Fardin Khabaz,Elda Hegmann

DOI: https://doi.org/10.1002/marc.202300717

IF: 5.006

2024-03-08

Macromolecular Rapid Communications

Abstract:We are presenting here a rheological study of a biocompatible and biodegradable liquid crystal elastomer (LCE) ink for 3D printing. These materials have shown that their structural variations have an effect on morphology, mechanical properties, alignment and their impact on cell response. Within the last decade LCEs have been extensively studied as potential printing materials for soft robotics applications, due to the actuation properties that are produced when LC moieties are induced through external stimuli. In this report we utilize experiments and coarse‐grained molecular dynamics to study the macroscopic rheology of LCEs in nonlinear shear flow. Results from the shear flow simulations are in line with the outcomes of our experimental investigations. We believe the insights from these results can be used to design and print new material with desirable properties necessary for targeted applications. This article is protected by copyright. All rights reserved

polymer science
Recent Advances in 4D Printing of Liquid Crystal Elastomers

Mei Chen,Ming Gao,Lichun Bai,Han Zheng,H. Jerry Qi,Kun Zhou

DOI: https://doi.org/10.1002/adma.202209566

IF: 29.4

2022-12-04

Advanced Materials

Abstract:Liquid crystal elastomers (LCEs) are renowned for their large, reversible, and anisotropic shape change in response to various external stimuli due to their lightly crosslinked polymer networks with an oriented mesogen direction, thus showing great potential for applications in robotics, bio‐medics, electronics, optics, and energy. To fully take advantage of the anisotropic stimuli‐responsive behaviors of LCEs, it is preferable to achieve a locally controlled mesogen alignment into monodomain orientations. In recent years, the application of four‐dimensional (4D) printing to LCEs opens new doors for simultaneously programming the mesogen alignment and the three‐dimensional geometry, offering more opportunities and higher feasibility for the fabrication of 4D‐printed LCE objects with desirable stimuli‐responsive properties. In this paper, the state‐of‐the‐art advances in 4D printing of LCEs are reviewed, with emphasis on both the mechanisms and potential applications. First, the fundamental properties of LCEs and the working principles of the representative 4D printing techniques are briefly introduced. Then, the fabrication of LCEs by 4D printing techniques and the advantages over conventional manufacturing methods are demonstrated. Finally, perspectives on the current challenges and potential development trends towards the 4D printing of LCEs are discussed, which might shed light on future research directions in this new field. This article is protected by copyright. All rights reserved

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Fabrication process of smooth functionally graded materials through a real-time inline control of the component ratio

Weiwei Guo,Zhaoliang Jiang,Cheng Zhang,Li Zhao,Zongxiang Jiang,Xinde Li,Guopeng Chen

DOI: https://doi.org/10.1016/j.jeurceramsoc.2021.09.037

IF: 5.7

2021-12-01

Journal of the European Ceramic Society

Abstract:Functionally graded materials (FGMs) play an essential role in tissue engineering because of their satisfactory histocompatibility and excellent mechanical performance. While traditional manufacturing methods allow production of simple FGMs, precise control of composition and customized property at transition between the dissimilar materials is still a challenge. Here, an extrusion-based functionally graded additive manufacturing (FGAM) platform was developed to generate smooth graded parts by thrusting out monolithic cylindrical filaments with high viscosity. Furthermore, the rheological properties, hydrodynamic behavior, and mixed homogeneity of the non-Newtonian fluids were studied. Therefore, the appropriate solid contents, alternative energy-efficient mixers, and optimized printing parameters were proved to be beneficial for an outstanding deposition effect of the suspension. Ultimately, an object with smooth gradient was successfully manufactured. The validity of this strategy was verified via optical microscopy combined with an image processing method to gauge homogeneity and a scanning electron microscope to investigate graded composition and microstructure.

materials science, ceramics
4D Printing of Freestanding Liquid Crystal Elastomers via Hybrid Additive Manufacturing

Xirui Peng,Shuai Wu,Xiaohao Sun,Liang Yue,S. Macrae Montgomery,Frédéric Demoly,Kun Zhou,Ruike Renee Zhao,H. Jerry Qi

DOI: https://doi.org/10.1002/adma.202204890

IF: 29.4

2022-08-15

Advanced Materials

Abstract:Liquid crystal elastomers (LCE) are appealing candidates among active materials for 4D printing, due to their reversible, programmable, and rapid actuation capabilities. Recent progress has been made on direct ink writing (DIW) or digital light processing (DLP) to print LCEs with certain actuation. However, it remains a challenge to achieve complicated structures, such as spatial lattices with large actuation, due to the limitation of printing LCEs on the build platform or the previous layer. Herein, we propose a novel method to 4D print freestanding LCEs on‐the‐fly by using laser‐assisted DIW with an actuation strain up to ‐40%. This process is further hybridized with the DLP method for optional structural or removable supports to create active 3D architectures in a one‐step additive process. We demonstrate that various objects, including hybrid active lattices, active tensegrity, an actuator with tunable stability, and 3D spatial LCE lattices, can be additively fabricated. The combination of DIW‐printed functionally freestanding LCEs with the DLP‐printed supporting structures thus provides new design freedom and fabrication capability for applications including soft robotics, smart structures, active metamaterials, and smart wearable devices. This article is protected by copyright. All rights reserved

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Free-Form Liquid Crystal Elastomers via Embedded 4D Printing

Luke McDougall,Jeremy Herman,Emily Huntley,Samuel Leguizamon,Adam Cook,Timothy White,Bryan Kaehr,Devin J Roach

DOI: https://doi.org/10.1021/acsami.3c14783

2023-12-20

Abstract:Liquid crystal elastomers (LCEs) are a class of active materials that can generate rapid, reversible mechanical actuation in response to external stimuli. Fabrication methods for LCEs have remained a topic of intense research interest in recent years. One promising approach, termed 4D printing, combines the advantages of 3D printing with responsive materials, such as LCEs, to generate smart structures that not only possess user-defined static shapes but also can change their shape over time. To date, 4D-printed LCE structures have been limited to flat objects, restricting shape complexity and associated actuation for smart structure applications. In this work, we report the development of embedded 4D printing to extrude hydrophobic LCE ink into an aqueous, thixotropic gel matrix to produce free-standing, free-form 3D architectures without sacrificing the mechanical actuation properties. The ability to 4D print complex, free-standing 3D LCE architectures opens new avenues for the design and development of functional and responsive systems, such as reconfigurable metamaterials, soft robotics, or biomedical devices.

Three-dimensional printing of functionally graded liquid crystal elastomer

3D Printing of Reprogrammable Liquid Crystal Elastomers with Exchangeable Boronic Ester Bonds

Shape Memory Behaviors of 3D Printed Liquid Crystal Elastomers

4D Printing of Freestanding Liquid Crystal Elastomers via Hybrid Additive Manufacturing (Adv. Mater. 39/2022)

Microfluidic 3D Printing of Emulsion Ink for Engineering Porous Functionally Graded Materials

4D Printing of High-Performance Thermal-Responsive Liquid Metal Elastomers Driven by Embedded Microliquid Chambers

Advances in 4D printing of liquid crystalline elastomers: materials, techniques, and applications

Three-Dimensional Coprinting Of Liquid Metals For Directly Fabricating Stretchable Electronics

3D Printing of Near-Ambient Responsive Liquid Crystal Elastomers with Enhanced Nematic Order and Pluralized Transformation

Programmable 3D Shape-Change Liquid Crystalline Elastomer Based on a Vertically Aligned Monodomain with Cross-link Gradient

Programmable spatial deformation by controllable off-center freestanding 4D printing of continuous fiber reinforced liquid crystal elastomer composites

Grayscale digital light processing 3D printing for highly functionally graded materials

Digital Light Processing-Based 3D Printing of Cell-Seeding Hydrogel Scaffolds with Regionally Varied Stiffness

Guided Folding of Nematic Liquid Crystal Elastomer Sheets into 3D via Patterned 1D Microchannels

Fast Digital Patterning of Surface Topography Toward Three-Dimensional Shape-Changing Structures

High-precision 3D printing of multi-branch vascular scaffold with plasticized PLCL thermoplastic elastomer

A Molecular Rheology Dynamics Study on 3D Printing of Liquid Crystal Elastomers

Recent Advances in 4D Printing of Liquid Crystal Elastomers

Fabrication process of smooth functionally graded materials through a real-time inline control of the component ratio

4D Printing of Freestanding Liquid Crystal Elastomers via Hybrid Additive Manufacturing

Free-Form Liquid Crystal Elastomers via Embedded 4D Printing