Abstract:This work addresses the topic of extrusion-based additive manufacturing (filament-based material extrusion) of patient-specific biofunctional maxillofacial implants. The technical approach was chosen to overcome the shortcomings of medically established fabrication processes such as a limited availability of materials or long manufacturing times. The goal of the work was a successful fabrication of basic implants for defect reconstruction. The underlying vision is the implants’ clinic-internal and operation-accompanying application. Following a literature search, a material selection was conducted. Digitally prepared three-dimensional (3D) models dealing with two representative mandible bone defects were printed based on the material selection. An ex-vivo model of the implant environment evaluated dimensional and fitting traits of the implants. Glycol-modified PET (PETG) and thermoplastic polyurethane (TPU) were finally selected. These plastics had high cell acceptance, good mechanical properties, and optimal printability. The subsequent fabrication process yielded two different implant strategies: the standard implant made of PETG with a build-up rate of approximately 10 g/h, and the biofunctional performance implant with a TPU shell and a PETG core with a build-up rate of approximately 4 g/h. The standard implant is meant to be intraoperatively applied, as the print time is below three hours even for larger skull defects. Standard implants proved to be well fitting, mechanically stable and cleanly printed. In addition, the hybrid implant showed particularly cell-friendly behavior due to the chemical constitution of the TPU shell and great impact stability because of the crack-absorbing TPU/PETG combination. This biofunctional constellation could be used in specific reconstructive patient cases and is suitable for pre-operative manufacturing based on radiological image scans of the defect. In summary, filament-based material extrusion has been identified as a suitable manufacturing method for personalized implants in the maxillofacial area. A further clinical and mechanical study is recommended.

Design and 3D printing of ceramic maxillofacial prosthesis with gradient pores based on Voronoi-Tessellation principle

Design and 3D printing of integrated bionic porous ceramic maxillofacial prosthesis

[Application of Three-Dimensional Printing Technique in Repair and Reconstruction of Maxillofacial Bone Defect].

Biofunctional Glycol-Modified Polyethylene Terephthalate and Thermoplastic Polyurethane Implants by Extrusion-Based Additive Manufacturing for Medical 3D Maxillofacial Defect Reconstruction

Digital Light Processing Strength-Strong Ultra-Thin Bioceramic Scaffolds for Challengeable Orbital Bone Regeneration and Repair in Situ

Fabrication of Low Cost Soft Tissue Prostheses with the Desktop 3D Printer

Digital light processing of β-tricalcium phosphate bioceramic scaffolds with controllable porous structures for patient specific craniomaxillofacial bone reconstruction

Digital light printing of zirconia/resin composite material with biomimetic graded design for dental application

A TMPS-designed personalized mandibular scaffolds with optimized SLA parameters and mechanical properties

Individually Prefabricated Prosthesis for Maxilla Reconstruction

Highly Malleable Personalized Prostheses with Hierarchical Microstructure Boost the Long‐Term Osteointegration in Irregular Craniofacial Reconstruction

Research on Design and Performance of High-Performance Porous Structure Based on 3D Printing Technology

Computer-aided Porous Implant Design for Cranio-Maxillofacial Defect Restoration

[Design and Fabrication of Porous Implants Manufactured by 3D Printing]

Design of Porous Structure Based on the Voronoi Diagram and Stress Line for Better Stress Shielding Relief and Permeability

The Feasibility of Prosthesis Design with Gradient Porous Structural

Porous structure design and properties of dental implants

Additive manufacturing of reconstruction devices for maxillofacial surgery: design and accuracy assessment of a mandibular plate prototype

Modeling, simulation, and experimental study of personalized porous tooth structure formed by laser selective melting (SLM)

Study on Digital Design and Manufacturing Techniques to Realize Precise Maxillofacial Prostheses Surgery

Fabrication of Customised Maxillo‐facial Prosthesis Using Computer‐aided Design and Rapid Prototyping Techniques